Register
Help
Remember Me?
Home
Forum
What's New?
Activity Stream
New Posts
New Group Messages
New Events
Mark Forums Read
Advanced Search
Home
Activity Stream
If this is your first visit, be sure to check out the
FAQ
by clicking the link above. You may have to
register
before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
Activity Stream
Filter
Sort By
Time
Show
Recent
Recent
Popular
Popular
Anytime
Anytime
Last 24 Hours
Last 24 Hours
Last 7 Days
Last 7 Days
Last 30 Days
Last 30 Days
All
All
Photos
Photos
Forum
Forums
Groups
Groups
New Activity (
)
Please reload this page to view the 200+ new activity items that have been created.
Older Activity
11 Minutes Ago
hmartinp
replied to a thread
Phaser 6180mfp Transfer Belt Reset ?
in
Xerox
This looks just like the one I took out! I see it here for $35 (chip is on the bottom).... 675K47088-CHIP - Xerox 6180 Transfer Belt Chip Item Inc.
see more
3 replies | 1535 view(s)
20 Minutes Ago
Synaux
replied to a thread
Bizhub C280 noise
in
Konica Minolta
Not that I have seen, then again, I make it a habit to vacuum waste toner out of the tranf belts probably more frequently than most--this practice...
see more
14 replies | 420 view(s)
20 Minutes Ago
Phil B.
replied to a thread
MFP Firmware reload on C224e
in
Konica Minolta
from the Forum Rules: Discussion of illegal activities such as software and music piracy and other intellectual property violations are not...
see more
65 replies | 14254 view(s)
32 Minutes Ago
rockdude
replied to a thread
Phaser 6180mfp Transfer Belt Reset ?
in
Xerox
Not sure myself (Might be a Pico fuse). But here is the replacement board from item inc. 675K47088-CHIP Good luck
see more
3 replies | 1535 view(s)
34 Minutes Ago
tsbservice
replied to a thread
4 series fuser rebuilds ???
in
Konica Minolta
As copyman said, forget about C5/6/754e fusers to replace smaller. They are IH coil heated. I have no parts manual for non 'e' models, but after...
see more
7 replies | 246 view(s)
36 Minutes Ago
tecnosrc
replied to a thread
anyone need toshiba firmware
in
Toshiba
Hello albenbalinong, yes i still need this firmware. Regard.
see more
45 replies | 11296 view(s)
39 Minutes Ago
KennethHycle
posted a
visitor message
on
Kennethkah's
profile
Doxycycline generic antabuse where to buy tetracycline synthroid levothyroxine metformin generic propecia
see more
40 Minutes Ago
steve1973
replied to a thread
Ricoh MPC 3003 K Drum
in
Ricoh, Savin, Gestetner, Lanier
Problem sorted, thanks to all who posted - removed Y/M/C dev units, fuser and ITB assembly, could then see much better especially through right door,...
see more
15 replies | 609 view(s)
1 Hour Ago
fshead
replied to a thread
Aficio SPC242 / SC543
in
Ricoh, Savin, Gestetner, Lanier
it means they have a special sender
see more
10 replies | 8941 view(s)
1 Hour Ago
dustzona
replied to a thread
Sharp MX-M620 developer on the loose
in
Sharp
It is definitely developer . The developing unit does not show signs leaking out the side. However the main charge and the dv unit are originals. I...
see more
3 replies | 112 view(s)
1 Hour Ago
fshead
replied to a thread
MP 7001 transfer unit solenoid strange one.
in
Ricoh, Savin, Gestetner, Lanier
does the problem follow the 7001 or the transfer unit,meaning when you swapped out transfer units did it fix the mp7001?
see more
2 replies | 74 view(s)
1 Hour Ago
Thayer
replied to a thread
[Electrical]
change hdd in 456
in
Toshiba
That is what I was always told. If you find out how, please share. Thanks
see more
3 replies | 87 view(s)
1 Hour Ago
Synaux
replied to a thread
4 series fuser rebuilds ???
in
Konica Minolta
Well this is a lot more curious when you look at the prices for these fusers new: c224/264/284/364/368/308 fuser: $431.95 Shipping Weight/Size:...
see more
7 replies | 246 view(s)
1 Hour Ago
ARMAN.MZ
replied to a thread
[Electrical]
change hdd in 456
in
Toshiba
I saw 455 hdd (normal hdd) installed to 456 (replace with wipe hdd)
see more
3 replies | 87 view(s)
1 Hour Ago
burak
started a thread
[Error Code]
canon imagepress c1+ starter
in
Canon
Canon c1+ starterHello Guys, How to use the canon c1+ Starter product? developer ASSEMBLY should I use it all? Help me please
see more
0 replies | 36 view(s)
1 Hour Ago
Phil B.
replied to a thread
Installation Image Press C1 + Image Press Server Q1
in
Canon
OLD THREAD not on topic for this thread... START NEW THREAD
see more
27 replies | 5914 view(s)
More Activity
No More Results
No Recent Activity