can any one send me the procedure to replace hard disk in ir adv 6255?
can any one send me the procedure to replace hard disk in ir adv 6255?
HDD
1. Before Replacing
Perform the following operations. Be sure to get an approval from the user beforehand.
1) Backup of the set/registered data
Use the Remote UI
Management Settings > Data Management > Import/Export
Target data:
• Address List
• Forwarding Settings
• Settings/Registration
• Web Access Favorites
• Printer Settings
• Paper Information
2) Printing the set/registered data
Use the service mode
(under Level 1) COPIER > FUNCTION > MISC-P > USER-PRT
List of the set/registered data which cannot be backed up is printed.
2. After Replacing
1) HDD format
1-1) Start with the safe mode. (While pressing 2 and 8 keys simultaneously, turn ON the main power switch.)
1-2) Use SST to format all partitions.
2) Downloading system software
2-1) Use SST to download the system software (System, LANG, RUI and others).
3) Initializing the key, certificate and CA certificate
(under Level 2 in Service Mode) COPIER > FUNCTION > CLEAR > CA-KEY
4) Turning OFF and ON the main power switch
5) Restoring the backup data
Use the Remote UI
Management Settings > Data Management > Import/Export
6) Resetting/registering the data
While referring to the list of set/registered data which was printed before replacement, reset/register the data.
7) When the user generates and adds the encryption key, certificate and/or CA certificate, request the user to generate them again.
8) Executing “Auto Adjust Gradation (Full Adjust)”
Settings/Registration mode: Adjustment/Maintenance > Adjust Image Quality > Auto Adjust Gradation
NOTE:
When using the Card Reader and imageWARE Accounting Manager
Card ID used for imageWARE Accounting Manager is stored in the HDD, so NSA collection control is not enabled after the HDD replacement.
After the HDD is replaced, re-install the card ID from imageWARE Accounting Manager using the following procedures.
1) Go to COPIER > FUNCTION> INSTALL > CARD and enter the numerical value of the leading card which is used for Department ID. Then, press “OK” button.(e.g.: If
No.1 to No.1000 cards are used for Department ID, enter “1” of the leading card.)
2) After turning OFF and ON the main power switch, perform the following operations from Settings/Registration mode.
-In Management Settings > User Management > Department ID Management > Page Totals, be sure that “ID00000001” to “ID00001000” are created.
Set the following: Preferences > Network > TCP / IP Settings > IPv4 Settings> IP Address Settings > IP Address, Gateway Address, Subnet Mask
-In Management Settings > User Management> System Manager Information Settings> System Manager ID and System PIN, register any number for them. Then,
turn OFF and ON the main power switch.
-If “System Manager ID” and “System PIN” are not registered, “card registration to device” cannot be executed for the imageWARE Accounting Manager setting
operation.
3) Download the card ID from imageWARE Accounting Manager to the Main Body again.
4) After downloading is completed, go to Management Settings > User Management > Department ID Management > Page Totals. Be sure that only the downloaded card ID is displayed.
5) Print using the user card registered from imageWARE Accounting Manager. Be sure that the card information used for the target devices of imageWARE Accounting
Manager is collected.
CAUTION: Points to Caution when Using the System Software-installed HDD
When using the HDD which was installed the system software of the other machine (different serial number), be sure to format the HDD after the installation. If the HDD is
not formatted, the operation cannot be guaranteed.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
hello
please am still waiting for help on the firmware or sst ver 4.72
cheers
how can i got firmware for ir adv 6255. i have problem with harddisk
Bookmarks