how to use SST

[Anjaskaseto]

how the contents of the hard disk system canon IR4570 with a LAN cable. wear SST program....???

[teckat]

how the contents of the hard disk system canon IR4570 with a LAN cable. wear SST program....???

--------------------------------------------------------------------
You First need the iR4570 Firmware
Next you need the SST
Install SST
then Download & Register Firmware into SST
see below



imageRUNNER Service Support Tool Flash Connectivity

CROSSOVER CABLE
NORMAL POWER ON MODE
[Customers IP: 192.19.1.20 - Laptop: 192.19.1.21]
Connect in reference to customers IP Address
"CANNOT" PERFORM HD-FORMAT

CROSSOVER CABLE
FIXED IP MODE
[Set Laptop for 172.16.1.101]
"CANNOT" PERFORM HD-FORMAT

CROSSOVER CABLE
SAFE MODE
[HOLD DOWN 2 & 8, POWER "ON" Machine]
PERFORMING HD-FORMAT

================================================== ==
Preparing System Software files for the Service Support Tool
1. Download the series model Firmware File ( from your download location)
2. Execute/Unzip the series model file. This will place the file in the following location:
“C:\Canon File Folder\SST Service Support Tool Folder\SST Files”.
SST1.jpg
3. Start the Service Support Tool (SST) and select “Register Firmware”.
SST2.jpg
4. Right click the C: folder on the list and browse to the following location: “C:\Canon File
Folder\SST Service Support Tool Folder\SST Files\ (EXAMPLE > iR5075_V3_v43.02 ).
SST3.jpg
5. Click the search button and the Service Support Tool (SST) will search that folder for the
series model system software and propagate in the right of the SST screen.
6. Click the “Register” button to install the series model system software
SST4.jpg

SST CONNECTION_Printer_Laptop.jpg

[x3256]

--------------------------------------------------------------------
You First need the iR4570 Firmware
Next you need the SST
Install SST
then Download & Register Firmware into SST
see below



imageRUNNER Service Support Tool Flash Connectivity

CROSSOVER CABLE
NORMAL POWER ON MODE
[Customers IP: 192.19.1.20 - Laptop: 192.19.1.21]
Connect in reference to customers IP Address
"CANNOT" PERFORM HD-FORMAT

CROSSOVER CABLE
FIXED IP MODE
[Set Laptop for 172.16.1.101]
"CANNOT" PERFORM HD-FORMAT

CROSSOVER CABLE
SAFE MODE
[HOLD DOWN 2 & 8, POWER "ON" Machine]
PERFORMING HD-FORMAT

================================================== ==
Preparing System Software files for the Service Support Tool
1. Download the series model Firmware File ( from your download location)
2. Execute/Unzip the series model file. This will place the file in the following location:
“C:\Canon File Folder\SST Service Support Tool Folder\SST Files”.
SST1.jpg
3. Start the Service Support Tool (SST) and select “Register Firmware”.
SST2.jpg
4. Right click the C: folder on the list and browse to the following location: “C:\Canon File
Folder\SST Service Support Tool Folder\SST Files\ (EXAMPLE > iR5075_V3_v43.02 ).
SST3.jpg
5. Click the search button and the Service Support Tool (SST) will search that folder for the
series model system software and propagate in the right of the SST screen.
6. Click the “Register” button to install the series model system software
SST4.jpg

SST CONNECTION_Printer_Laptop.jpg

Sir i have followed this procedure and even after registering firmware my sst is not showing the model names in model drop box to connect its empty in win 10

[teckat]

u did something wrong.

Look here---- “C:\Canon File Folder\SST Service Support Tool Folder\SST Files
Do u see the Firmware Model Listed here ???

Firmware must be Registered into SST from the Initial Default Download Location.

if no

1. make sure u have only ONE version of SST installed on laptop
2. start all over again-- follow the prompts--Do not Change Default Location.