hello
i have Canon i-sensys MF623cn ,code error E015-0001
help me please
hello
i have Canon i-sensys MF623cn ,code error E015-0001
help me please
Developing Home Position Sensor did not detect.Probably timing issue.
Practice makes perfect
If it ain't broke, don't fix it
A picture is worth a thousand words
If you want something done right, you have to do it yourself
============================================
not sure if MF623cn is same as below model ????
-----------------------------------------------------------------------
on the MF634dw
E015-0001--- Cassette 1 lift-up error
Detection Description After lift-up of the Lifting Plate of the cassette of the host machine started, ON status of the Lifter
Sensor of the cassette of the host machine was not detected within the specified period of time.
Remedy 1. While the cassette of the host machine is removed, turn ON the power and insert the cassette,
then check the operation sound of the motor.
When there is operation sound of the motor, check if the Lifting Plate has been lifted up.
When the Lifting Plate has been lifted up:
1-1. Check that the Lifter Sensor of the cassette of the host machine is properly installed.
1-2. Check the harness/connector between the Engine Controller PCB and the Lifter Sensor.
1-3. Replace the Lifter Sensor.1-4. Replace the Engine Controller PCB.
When the Lifting Plate has not been lifted up:
2-1. Check the condition of the gear at the host machine side (missing teeth, swing).
2-2. Check the harness/connector between the Engine Controller PCB and the Lifter Solenoid of
the cassette of the host machine.
2-3. Replace the Lifter Solenoid.
2-4. Replace the Pickup Motor of the cassette of the host machine.
2-5. Replace the Driver PCB.
2-6. Replace the Engine Controller PCB.
When there is no operation sound of the motor, check the followings:
3-1. Check the harness/connector between the Engine Controller PCB and the Pickup Motor of
the cassette of the host machine.
3-2. Check the condition of the gear at the host machine side (missing teeth, swing).
3-3. Check the Pickup Motor.
3-4. Replace the Driver PCB.
3-5. Replace the Engine Controller PCB.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
thank's
when Remove the thermal fuse cable from the power supply "SECONDARY PRIMARY" (FM0-3910(200v)) and run machine display error E000-0000, then off machine and reconnect the cable , run machine It works well for an hour after it returns off the error E015-0001
Where is the problem exactly ?
u can't remove thermal connection cable and expect printer to not error out in a E000-000 code
are u a tech ?? if so u would know that
====================
did u check this
E015 - 0001 = Error in Developing Disengagement Motor
Description = Change in signal status of the Developing Home Position Sensor could not be detected althougha specified period of time has passed after rotating the Main Motor for engagement/disengagement operation of the Developing Cylinder.
Remedy =
1. Check the connectors connecting the Developing Home Position Sensor, Main Motorand the DC Controller PCB.
2. Replace the Developing Home Position Sensor.
3. Replace the Main Motor.
4. Replace the DC Controller PCB
Last edited by teckat; 04-16-2017 at 03:22 PM.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
[QUOTE=teckat;559303]
u can't remove thermal connection cable and expect printer to not error out in a E000-000 code
are u a tech ?? if so u would know that
====================
were is a link to Basic USER GUIDE e-Manual----i-SENSYS
MF729Cx MF728Cdw MF724Cdw MF628Cw MF623Cn
http://ug.oipsrv.net/USRMA-0340-zz-S...tmls/home.html
================================================== ====================================
i-SENSYS MF729Cx, MF728Cdw, MF726Cw, MF724Cdw, MF628Cw, MF624Cw , MF623Cn Series
did u check this
E015 - 0001 = Error in Developing Disengagement Motor
Description = Change in signal status of the Developing Home Position Sensor could not be detected althougha specified period of time has passed after rotating the Main Motor for engagement/disengagement operation of the Developing Cylinder.
Remedy =
1. Check the connectors connecting the Developing Home Position Sensor, Main Motorand the DC Controller PCB.
2. Replace the Developing Home Position Sensor.
3. Replace the Main Motor.
4. Replace the DC Controller PCB
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
thank's teckat
did you have service manual for MF623Cn or Series ?
so the code E015-001 is disappear, but the display code error E000-0000 after moments
help me please
The DC controller determines failures of the fixing assembly under conditions below to stop the fixing heater drive signal output
(FSRD+, FSRD-) and shut off relay and power supply to the heater. At the same time, it notifies the failure occurrence to the main
controller.
1. Start-up failure detection
• The thermistor temperature does not exceed startup temperature 1 within the pre-defined time after start-up of the heater
from the waiting status.
• The thermistor temperature does not exceed startup temperature 2 within the pre-defined time after reaching startup
temperature 1 upon start-up of the heater from the waiting status.
• The thermistor temperature does not reach the target temperature within the pre-defined time after heater temperature
control during initial rotation.
[Related error code] : E000-0000
E000 0000= Error in temperature rising of Fixing Assembly
Temperature of the Fixing Assembly did not reach a certain temperature within the specified
period of time.
1. Check the connector connection between the Fixing Assembly and the DC Controller
PCB.
2. Replace the Fixing Assembly.
3. Replace the DC Controller PCB.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
Bookmarks