Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: Ir 2870

  1. #1
    Technician
    Join Date
    May 2011
    Posts
    41
    Rep Power
    27

    Ir 2870

    Error code e00024_001.changed dp unit .again showing after 5k copies.
    May be tonner hopper sensor

  2. #2
    Service Manager 10,000+ Posts
    Ir 2870

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Ir 2870

    E024-0001 Error Code:

    Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Blow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor.


    However, re-attachment of the sensor also solves the symptom.

    When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021].

    If the setting is "1", re-attach the toner sensor.
    ================================================== =============


    One problem found has been the toner sensor scraper blade in the developer not making contact with the surface of the toner sensor.

    To check the toner sensor scraper blade first set up a work area. Lay out several sheets of 11 x17 paper on the work surface.
    Disassembling the developer is a messy job.

    Remove the upper cover of the developer and then rotate the developer in a counter clock wise direction. Basically the cylinder should rotate so the toner is scraped off of the cylinder by the developer blade.

    If it is rotated in the wrong direction a large amount of toner will adhere to the developer cylinder and makes a mess.
    The toner sensor is located on the on the outside of the developer and part of it goes through the wall of the developer unit.




    Next look at the inside surface of the developer where the toner sensor is mounted while rotating the developer cylinder in the correct direction.
    There is a mylar scraper sheet that needs to touch the inside surface of the developer wall.

    In the image below the inside surface of the developer wall is being touched by the mylar scraper blade.
    If the blade is damaged or broken off the toner will not be cleaned off of the sensor and give the error code
    E024.
    If the blade is the problem the developer will need to be replaced.
    The part number for the developer is FM2-0287-010.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Technician
    Join Date
    May 2011
    Posts
    41
    Rep Power
    27

    Re: Ir 2870

    Quote Originally Posted by teckat View Post
    E024-0001 Error Code:

    Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Blow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor.


    However, re-attachment of the sensor also solves the symptom.

    When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021].

    If the setting is "1", re-attach the toner sensor.
    ================================================== =============


    One problem found has been the toner sensor scraper blade in the developer not making contact with the surface of the toner sensor.

    To check the toner sensor scraper blade first set up a work area. Lay out several sheets of 11 x17 paper on the work surface.
    Disassembling the developer is a messy job.

    Remove the upper cover of the developer and then rotate the developer in a counter clock wise direction. Basically the cylinder should rotate so the toner is scraped off of the cylinder by the developer blade.

    If it is rotated in the wrong direction a large amount of toner will adhere to the developer cylinder and makes a mess.
    The toner sensor is located on the on the outside of the developer and part of it goes through the wall of the developer unit.




    Next look at the inside surface of the developer where the toner sensor is mounted while rotating the developer cylinder in the correct direction.
    There is a mylar scraper sheet that needs to touch the inside surface of the developer wall.

    In the image below the inside surface of the developer wall is being touched by the mylar scraper blade.
    If the blade is damaged or broken off the toner will not be cleaned off of the sensor and give the error code
    E024.
    If the blade is the problem the developer will need to be replaced.
    The part number for the developer is FM2-0287-010.

    thanks sir.problem sorted.toner sensor was shorting.replaced same.
    Machine working ok now.lets see

  4. #4
    Service Manager 10,000+ Posts
    Ir 2870

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Ir 2870

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here