Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Trusted Tech 50+ Posts markdmt's Avatar
    Join Date
    Dec 2009
    Location
    north salt lake, utah
    Posts
    74
    Rep Power
    30

    ImagePress C6000VP AB2 LTRR jam 1042

    I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
    10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

    I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
    finisher version 4101.0.0.0.0.0.0
    AB2
    Controller 9201.8203.7903

  2. #2
    Service Manager 10,000+ Posts
    ImagePress C6000VP  AB2 LTRR jam 1042

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by markdmt View Post
    I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
    10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

    I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
    finisher version 4101.0.0.0.0.0.0
    AB2
    Controller 9201.8203.7903

    1. Try Adjusting the Saddle Alignment Reference


    2. C7000VP / C6000VP / C6000, Saddle Finisher-
    AB2

    Check PS106 in the Edge Stopper Assembly for proper operation.
    Replace the sensor if necessary.
    Also, the sensor cable to PS106 in the Edge Stopper Assembly flexes up and down with the Edge Stopper and may have a break in the wiring as was found in some cases.
    See picture below for cable location and part number, (Figure L57 in parts catalog).



    Last edited by teckat; 06-01-2017 at 03:12 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Trusted Tech 50+ Posts markdmt's Avatar
    Join Date
    Dec 2009
    Location
    north salt lake, utah
    Posts
    74
    Rep Power
    30

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by teckat View Post

    1. Try Adjusting the Saddle Alignment Reference


    2. C7000VP / C6000VP / C6000, Saddle Finisher-
    AB2

    Check PS106 in the Edge Stopper Assembly for proper operation.
    Replace the sensor if necessary.
    Also, the sensor cable to PS106 in the Edge Stopper Assembly flexes up and down with the Edge Stopper and may have a break in the wiring as was found in some cases.
    See picture below for cable location and part number, (Figure L57 in parts catalog).



    Forgive me for not knowing how to set the Saddle Alignment Reference? is that part of the adjustments when replacing the finisher control eeprom? section 5 of the AB2 service manual?
    I don't think this is a sensor issue because i have swapped with two other finishers. however all three of these have had finisher boards replaced and new eeproms. These all seem to work like normal except this issue with the paper coming down and stopping before it goes into the saddle folder area. Thanks

  4. #4
    Service Manager 10,000+ Posts
    ImagePress C6000VP  AB2 LTRR jam 1042

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by markdmt View Post
    I have a imagepress c6000VP that when i try and run LTRR saddle booklets it keeps jamming with a 1042
    10 42 PS101 Saddle inlet sensor When implementing the specified time of feeding since the lower path sensor was on, the saddle inlet sensor is not on.

    I have tried 2 separate AB2 finishers with the same code? not sure if this might be a software issue? any help would be appreciated.
    finisher version 4101.0.0.0.0.0.0
    AB2
    Controller 9201.8203.7903

    in manual 5-37/7
    5.3.2.15 Adjusting the Saddle Alignment Reference



    does LTR-R run ok into all Finisher trays (non-Booklet mode)
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Trusted Tech 50+ Posts markdmt's Avatar
    Join Date
    Dec 2009
    Location
    north salt lake, utah
    Posts
    74
    Rep Power
    30

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by teckat View Post

    in manual 5-37/7
    5.3.2.15 Adjusting the Saddle Alignment Reference



    does LTR-R run ok into all Finisher trays (non-Booklet mode)


    Not sure on that. i had them offline fold and staple the little job but need to get it fixed. i will get back to it. THX

  6. #6
    Trusted Tech 50+ Posts markdmt's Avatar
    Join Date
    Dec 2009
    Location
    north salt lake, utah
    Posts
    74
    Rep Power
    30

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by markdmt View Post
    Not sure on that. i had them offline fold and staple the little job but need to get it fixed. i will get back to it. THX
    the LTR-R does run into both upper trays without issue. just looks like it stops at the buffer waiting area and jams before it even goes into the folder area.

  7. #7
    Service Manager 10,000+ Posts
    ImagePress C6000VP  AB2 LTRR jam 1042

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by markdmt View Post
    the LTR-R does run into both upper trays without issue. just looks like it stops at the buffer waiting area and jams before it even goes into the folder area.


    Does booklet LTRR jam using print driver and a walk up test on control panel ?
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #8
    Trusted Tech 50+ Posts markdmt's Avatar
    Join Date
    Dec 2009
    Location
    north salt lake, utah
    Posts
    74
    Rep Power
    30

    Re: ImagePress C6000VP AB2 LTRR jam 1042

    Quote Originally Posted by teckat View Post
    Does booklet LTRR jam using print driver and a walk up test on control panel ?
    Yes

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here