Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Sep 2011
    Posts
    127
    Rep Power
    14

    Canon scanner Dr 6030c wont feed help

    Hi Folks,
    I vivited a cust with a Canon DR 6030c scanner that doesnt even try to feed the paper, I noticed the feeder roller was lower poistion. I removed cover, an spun motor by hand, for the pick up roller where it should be in the "up" position. I checked to see that all the feed rollers were turning, not binding..has anyone replaced the feed motor/board..?
    I'm new to this machine so looking for experienced folks..even better if so, would anyone have part number, or part to sell ..??
    Thanks,
    Jaime
    Indep. Copier Svc.,CT.


  2. #2
    Service Manager 10,000+ Posts
    Canon scanner Dr 6030c wont feed help

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,208
    Rep Power
    215

    Re: Canon scanner Dr 6030c wont feed help

    Quote Originally Posted by jper34 View Post
    Hi Folks,
    I vivited a cust with a Canon DR 6030c scanner that doesnt even try to feed the paper, I noticed the feeder roller was lower poistion. I removed cover, an spun motor by hand, for the pick up roller where it should be in the "up" position. I checked to see that all the feed rollers were turning, not binding..has anyone replaced the feed motor/board..?
    I'm new to this machine so looking for experienced folks..even better if so, would anyone have part number, or part to sell ..??
    Thanks,
    Jaime
    Indep. Copier Svc.,CT.

    Do The Pickup Rollers retract when the machine is powered on.

    The Stopper Plates are also in the down position.
    The Feed Selection Lever is in the correct position (up) for separation.


    In this case, entering the Service Tool program and activating all the components resolved the issue.
    In the tool, all the sensors activated correctly and the tech was able to run the Main Motor, Eject Motor, Pickup Motor, Regist Clutch, and Feed Clutch with no problem.

    After exiting the Service Tool and powering the scanner Off/On, everything worked properly.


    ================================================== =======
    New DR 6030c feed roller.jpg


    Feed Roller will
    Not Lower to the Paper.

    In a few cases the Worm Gear on the motor was not making constant contact with the gear for the Feed Roller.

    By loosening the screws for the motor and then tighten them again the scanner worked properly.




    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Senior Tech 100+ Posts
    Join Date
    Sep 2011
    Posts
    127
    Rep Power
    14

    Re: Canon scanner Dr 6030c wont feed help

    Thanks Tek...I just ealized it was the DR 6010c series, not the 6030c series,....I'm hoping its the motor..your thoughts?


  4. #4
    Service Manager 10,000+ Posts
    Canon scanner Dr 6030c wont feed help

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,208
    Rep Power
    215

    Re: Canon scanner Dr 6030c wont feed help

    Quote Originally Posted by jper34 View Post
    Thanks Tek...I just ealized it was the DR 6010c series, not the 6030c series,....I'm hoping its the motor..your thoughts?



    -----Paper does not feed. The pickup and feed rollers do not rotate.

    ensure that the belts and gears driven by the motor are normal.


    what exactly is happening on power on ?




    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Senior Tech 100+ Posts
    Join Date
    Sep 2011
    Posts
    127
    Rep Power
    14

    Re: Canon scanner Dr 6030c wont feed help

    after power up, the pick up rollers dont even try to spin, I turned drive belt by hand to check for any binds, then turned it to get pick up roller in home position(up). I re seated motor connector, that didnt help. I should have removed motor an then re power to see if motor tries to turn, but I dont think it does, didnt hear anything from that motor. I'm guessing the motor should spin after power up, when you try to scan via computer, it just sits there...no error code comes up, or paper jam notice. I ordered a motor, only $50.00, but if that doesnt work, any ideas..?


  6. #6
    Senior Tech 100+ Posts
    Join Date
    Sep 2011
    Posts
    127
    Rep Power
    14

    Re: Canon scanner Dr 6030c wont feed help

    Hi Folks,
    the motor did repair the , no feed issue,..Thank God !!!!


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here