Results 1 to 5 of 5
  1. #1
    Senior Tech 100+ Posts
    Join Date
    Jan 2014
    Posts
    108
    Rep Power
    9

    Lite podeck B1 within imagepress C800

    Dears all:
    we face problem with lite pod-deck B1 within image-press c800
    that the following message appear:
    "paper source needs to be checked (call service rep.)"
    the following procedures had taken
    1-cleaning all sensors within the lite pod-deck
    2-clear DC-CON and error *hint
    3-cleaing all sensors within feeding section assembly.
    *hint
    "when clearing DC-CON. the message disappear but jam occurred and when shutdown the machine message return to appear again
    so we ask your help
    thanks in advance.



  2. #2
    Technician
    Join Date
    Jul 2017
    Location
    Montvale
    Posts
    22
    Rep Power
    1

    Re: Lite podeck B1 within imagepress C800

    There is a safety switch at bottom of unit which detects if the tray goes too far down, maybe that isn't in correct position, also what jam code did it you get that required you to power cycle the engine.


  3. #3
    Senior Tech 100+ Posts
    Join Date
    Jan 2014
    Posts
    108
    Rep Power
    9

    Re: Lite podeck B1 within imagepress C800

    Quote Originally Posted by NorthW View Post
    There is a safety switch at bottom of unit which detects if the tray goes too far down, maybe that isn't in correct position, also what jam code did it you get that required you to power cycle the engine.
    yes safety switches has checked
    jam code (10B)


  4. #4
    Service Manager 10,000+ Posts
    Lite podeck B1 within imagepress C800

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,207
    Rep Power
    215

    Re: Lite podeck B1 within imagepress C800

    Quote Originally Posted by khattab.al.masry View Post
    Dears all:
    we face problem with lite pod-deck B1 within image-press c800
    that the following message appear:
    "paper source needs to be checked (call service rep.)"
    the following procedures had taken
    1-cleaning all sensors within the lite pod-deck
    2-clear DC-CON and error *hint
    3-cleaing all sensors within feeding section assembly.
    *hint
    "when clearing DC-CON. the message disappear but jam occurred and when shutdown the machine message return to appear again
    so we ask your help
    thanks in advance.


    ????
    DCON backup and clear and re-inputting the DCON values manually, ????

    System Software is at the current version.


    Pod Deck Lite-B1
    Title :
    Paper Source Needs to be Checked Message

    ~~~~~~~~~~~~~~~

    There was a small bracket on the side of the Pod Deck that was bent preventing the drawer from closing all the way.

    The bracket was repaired and then the drawer closed, but the error message remained.

    Since there was a damaged bracket, continued to inspect the stock assembly and cavity where the stock assembly slides into.

    _Found that the bracket to SW3 (Deck Lifter Lower Limit Switch) was bent not activating the switch correctly.
    Reforming the bracket for SW3 (Deck Lifter Lower Limit Switch) resolved the issue.

    The following image shows the location of SW3.





    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Service Manager 10,000+ Posts
    Lite podeck B1 within imagepress C800

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,207
    Rep Power
    215

    Re: Lite podeck B1 within imagepress C800

    After you've repaired the POD Deck Lite-B1, and for instance have replaced the Deck Driver PCB, first follow the steps in the Service Manual,

    1) Remove all sheets of paper from the Compartment.
    2) Turn on the host machine. The fan wind-power correction sequence is performed
    automatically.
    3) Execute the following item on the service mode.
    (Lv.1) COPIER> FUNCTION> CST> DK1-INT1 (Initialization when replacing the parts)
    4) Execute the following item on the service mode.
    (Lv.1) COPIER> FUNCTION> CST> PDK-A4
    4-1) Set the A4 paper in the Compartment to adjust and align it with the width of guide.
    4-2) Select the item, and then press OK key.
    4-3) After automatic adjustment, the value is stored in the following item.
    (COPIER>ADJUST>CST-ADJ>PDK-A4)
    5) Execute the following item on the service mode.
    (Lv.1) COPIER> FUNCTION> CST> PDK-A5R
    5-1) Set the A5R paper in the Compartment to adjust and align it with the width of guide.
    5-2) Select the item, and then press OK key.
    5-3) After automatic adjustment, the value is stored in the following item.
    (COPIER>ADJUST>CST-ADJ>PDK-A5R).

    After this replacement, (just as an example of repair to the POD Deck Lite-B1, if the message still remains and you have updated Firmware to v36.01.02 or higher, enter Service Mode Level 1, COPIER > FUNCTION > CLEAR > and on the last screen you will see DK-RCV. Highlight this and run it. Power cycle the machine one more time and the message should be gone and the POD Deck Lite-B1 now fully functional.










    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here