thank you i will try the registration when i get home.
also i have not been able to get by step 3) Press [Printer Status/Settings].
it just gets stuck at check connections or please wait.
thank you i will try the registration when i get home.
also i have not been able to get by step 3) Press [Printer Status/Settings].
it just gets stuck at check connections or please wait.
H1 has three connections:
Crossover Cable from Printer to H1 box
Ethernet Cable from H1 box to Wall Network Connection
Interface Cable from H1 box to Printer.
Link to Service\Install Guide
Dropbox - docslide.com.br_imagepass-h1-color-network-printer-unit-h1-service-guide-2.pdf
Same links here
Canon ir c4080 Networking question
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
had some good results today. i got rid of the heavy smudging in the prints and i got the paperdesk up and feeding paper reliably. i tried the registration settings and couldnt figure out how to print the grid page.
i did try switching the interface to 0 but the copier would not pull dhcp or respond to ping on a static address. i think im missing the functionality for that.
reset the interface for the fiery and still cannot connect. did a sector check on the harddrive and it passed with no issues. and the drives smart also passed. but still will not open in the menu.
did u download and read the H1 service guide link above
Test Prints=Go into service mode level 1
under
COPIER>TEST>PG>TYPE
Performs test print when test print type number is entered and start key is turned ON. (This setting must always be
restored to 0 after making test print.)
under Type=enter #6 for Grid Pattern print out.
Entered number - Description
0 -Image from CCD (normal print)
1 -For development
2 -For development
3 -For development
4 -16 gradations
5 -Full-sheet half tones
6 -Grid
7 -For development
8 -For development
9 -For development
10 -MCYBk horizontal stripes
11 -For development
12 -YMCBk 64 gradations
13 -For development
14 -Full-color 16 gradations
15 to 100 For development
#6-#5 and #10 are the basic checks
DENS-Y/M/C/K= Used to adjust density of each color for test prints (TYPE = 5).
Setting values
0 to 255: Increasing the value increases the density.
[Factory default/After RAM clear: 128]
COLOR-Y/M/C/K Used to set output of each color for each TYPE.
For example, to set single-color M output, set "COLOR-M = 1", and make the other settings 0 (only single colors can be output).
Setting values
0: Don't output
1: Output
[Factory default/After RAM clear: 1]
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
i did read the manual but unless i missed something it didn't really show anything to troubleshoot it. i did plug a monitor into it and it booted to decompressing kernel. and from prior fiery experience it switched to the copier video output. and the diag display goes to 00.
i tried setting the pg type to 6 and then clicked ok. i figured after that i would hit the start button? and that caused it to make a normal copy from the glass. i did get it to print out a copy of all of its current settings but that was from a different menu.
after reading the registration guide the black laser lens is always set to the mid point. and is never adjusted could it have got shifted during transportation? the overall print is off the top of the page also.
Complete Re-Install of the H1 > just as if u were first doing a set up.
----------------------------------------------------------------------------------------------
First-Remove all connections cables(I/F Communications Cable,Cross Ethernet Cable, & Network Cable from H1 to Copier/also unplug H1 power cord.
*NEXT>>>>follow below EXACTLY AS SHOWN
1. Enter Service mode (Additional Functions > 2 and 8 > Additional Functions).
2. Select Copier > Option > Int-Face > IMG-CONT.
3. Change the setting of IMG-CONT back to "0"
4. Hit OK and (& follow the normal shutdown procedure of Printer) then Re-Boot the Copier.
5. Re-Enter Service mode (Additional Functions > 2 and 8 > Additional Functions).
6. Change the setting of IMG-CONT back to "3"
7. Hit OK and ( again >follow the Normal Shutdown Procedure of Printer)
8. With Printer "OFF", u now Connect all of the 3 Cables that were previously removed.>don't forget H1 POWER CORD--
9. Now > Power back up Printer
10. At the Control Panel, press [Printer] tab.
11. Press [Printer Status/Settings].
12. At the Languages Setup screen, select the name of the language you want to use, and then select OK.
Wait a few minutes.
13. Input of password Fiery .1 (exactly as shown )
14. In response, the machine will automatically show the Settings menu.
15. Be sure to at least select the following and make the appropriate settings in the indicated order:
[Server Setup], [Network Setup], and [Printer Setup].
Checking the Operation After Making the Settings
Print out a test page and a settings page as follows to make sure that all settings have correctly been made on
the machine and its host machine and that all connections are normal------
1) Press (=>) displayed at upper right on the LCD of the connecting device.
2) At the Control Panel, press [Print].
3) Press [Printer Status/Settings].
4) Make the following selections on the LCD:function>print page>test page/configuration.
Hopefully this Procedure will get u up and Running/Works about 90% of the time
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
ah i only did half of that. i did not power down the h1 or unplug the interface cable. ill give that a shot. fingers crossed!
Same thing happens. Comes up with wait a moment. And then please wait sometime after.
what should i be looking for on this list? also the network link lights keep turning off on the fiery like its crashing maybe and restarting the network.
Bookmarks