Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 38
  1. #21
    Technician
    Join Date
    Mar 2018
    Location
    Peabody
    Posts
    34
    Rep Power
    13

    Re: Reviving Canon IR c5180

    Where could one obtain system disk for the fiery? would Canon still supply them or would calling EFI be a better option?

    I have gotten the paper desk and the W1 finisher working. still need to clean the rollers on the finisher as papers slip past during the stapling.
    and today im going to check the lasers adjustments.

  2. #22
    Service Manager 10,000+ Posts
    Reviving Canon IR c5180

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Reviving Canon IR c5180

    Quote Originally Posted by nicko6113 View Post
    Where could one obtain system disk for the fiery? would Canon still supply them or would calling EFI be a better option?

    I have gotten the paper desk and the W1 finisher working. still need to clean the rollers on the finisher as papers slip past during the stapling.
    and today im going to check the lasers adjustments.


    Check your PM
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #23
    Technician
    Join Date
    Mar 2018
    Location
    Peabody
    Posts
    34
    Rep Power
    13

    Re: Reviving Canon IR c5180

    Didn't get any PM's yet.

  4. #24
    Service Manager 10,000+ Posts
    Reviving Canon IR c5180

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Reviving Canon IR c5180

    Quote Originally Posted by nicko6113 View Post
    Didn't get any PM's yet.


    Check now, also check your e-mail.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #25
    Technician
    Join Date
    Mar 2018
    Location
    Peabody
    Posts
    34
    Rep Power
    13

    Re: Reviving Canon IR c5180

    Good new i have gotten my fiery up and running thanks to teckat! fixed most of my registration issues with adjusting the transfer rail adjustment lever. all of my colors are lined up except for magenta its just a hair off. Also the cleaning blade seems to not be doing a great job. and the transfer belt is questionable print quality. Im going to order a new belt and blade and see how it does. but ill just run it now and see if the belt gets better.

  6. #26
    Service Manager 10,000+ Posts
    Reviving Canon IR c5180

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Reviving Canon IR c5180

    Quote Originally Posted by nicko6113 View Post
    Good new i have gotten my fiery up and running thanks to teckat! fixed most of my registration issues with adjusting the transfer rail adjustment lever. all of my colors are lined up except for magenta its just a hair off. Also the cleaning blade seems to not be doing a great job. and the transfer belt is questionable print quality. Im going to order a new belt and blade and see how it does. but ill just run it now and see if the belt gets better.

    welcome

    If u haven't so already, remove all drums, toners, ITB unit, slide out the fixing unit, remove ITB cleaning blade----take a flash light look at rail where the cleaning blade slides into --probably full of waste toner--best to vacuum out---if u have to hand wipe it out----before u do--place paper under area- to prevent dropping all over.

    Tip:--never place the waste container on the door while working---it will Tip Over--and cause major mess
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #27
    Technician
    Join Date
    Mar 2018
    Location
    Peabody
    Posts
    34
    Rep Power
    13

    Re: Reviving Canon IR c5180

    i will check again but i did get in there and vacuum it. the toner ends up on the back side of the blade and smears on the itb. which then causes the quick gradation test to make everything light. but during normal prints it will clear up.



    Shared album - Nick Solano - Google Photos
    Shared album - Nick Solano - Google Photos
    Shared album - Nick Solano - Google Photos

    the little smudging issue and the magenta being slightly to low.

    PS. can't embed pictures.

  8. #28
    Service Manager 10,000+ Posts
    Reviving Canon IR c5180

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Reviving Canon IR c5180

    Quote Originally Posted by nicko6113 View Post
    i will check again but i did get in there and vacuum it. the toner ends up on the back side of the blade and smears on the itb. which then causes the quick gradation test to make everything light. but during normal prints it will clear up.



    Shared album - Nick Solano - Google Photos
    Shared album - Nick Solano - Google Photos
    Shared album - Nick Solano - Google Photos

    the little smudging issue and the magenta being slightly to low.

    PS. can't embed pictures.
    Make sure the ITB underside metal plates are clean



    That flexible scraper on rail gets bent, causes issues.

    I would change the entire cleaning unit, not just the blade
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  9. #29
    Technician
    Join Date
    Mar 2018
    Location
    Peabody
    Posts
    34
    Rep Power
    13

    Re: Reviving Canon IR c5180

    the whole unit as in the metal casing around the blade. not just the blade itself?

    i did take the lower metal cover off of the itb but i was not looking for this issue at the time. but i did clean it. looked in good condition.

  10. #30
    Service Manager 10,000+ Posts
    Reviving Canon IR c5180

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Reviving Canon IR c5180

    Quote Originally Posted by nicko6113 View Post
    the whole unit as in the metal casing around the blade. not just the blade itself?

    i did take the lower metal cover off of the itb but i was not looking for this issue at the time. but i did clean it. looked in good condition.

    yes----because the cleaning cover rubber strip gets bent / gaps--that causes waste to drop

    FG6-8989-030 = TRANSFER CLEANING ASSEMBLY
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here