Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 13
  1. #1
    Senior Tech 250+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    480
    Rep Power
    21

    squeak Imagerunner advanced 400If

    Noise is coming from the roller set after the feed rollers in the upper tray. I shot some alcohol around the shaft/roller bushings, the noise went away. After added some oil and at the end of the day the customer called back. I was wondering if those sections are easy to remove? Does anyone have any objection to using a spray lubricant instead of removing the assemblies?


  2. #2
    Field Supervisor 500+ Posts dan7777's Avatar
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    611
    Rep Power
    22

    Re: squeak Imagerunner advanced 400If

    Quote Originally Posted by acsolutions View Post
    Noise is coming from the roller set after the feed rollers in the upper tray. I shot some alcohol around the shaft/roller bushings, the noise went away. After added some oil and at the end of the day the customer called back. I was wondering if those sections are easy to remove? Does anyone have any objection to using a spray lubricant instead of removing the assemblies?
    When you remove the right front door, right rear cover and right front cover it is not hard to take out. I used spray lubricant once and never used it again as it caused another issue. That was 25 years ago and I think I used wd40, did find out from another company it is an excellent roller cleaner. Most of my squeaks on that model come from the drum.


  3. #3
    Service Manager 2,500+ Posts
    squeak Imagerunner advanced 400If

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    2,699
    Rep Power
    41

    Re: squeak Imagerunner advanced 400If

    Quote Originally Posted by acsolutions View Post
    I was wondering if those sections are easy to remove? Does anyone have any objection to using a spray lubricant instead of removing the assemblies?
    REALLY? I BET you even sprayed that in the machine when the machine was ALIVE too didn't you?
    what OIL did you spray in there?

    did you know that the brass bushings in the Canon - HP - Ricoh machines DRY OUT if WD40 is used on them?

    YES! I do have an objection on half assing the job. PULL THE DAMN FEED ( OR ANY SECTION ) AND DO THE JOB PROPERLY!

    Get the damn manual and do the job the correct way.. the way you are doing it will bite your ass in the long run.


  4. #4
    Tech Specialist 1,000+ Posts Canuck's Avatar
    Join Date
    Nov 2007
    Location
    Southwestern Ontario
    Posts
    1,531
    Rep Power
    45

    Re: squeak Imagerunner advanced 400If

    Drums are notorious for squeaking. Oil them all the time....ends of primary(small drop on each end), pull out the drum ground clip on the end a little bit and put a dab of conductive grease, also a drop of oil on drum flanges ends(white plastic). Sometimes the delivery bushings in the fuser squeak(cheap, not Oilite). Drop of oil...


  5. #5
    Senior Tech 250+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    480
    Rep Power
    21

    Re: squeak Imagerunner advanced 400If

    No, I never used any spray lube. Unfortunately it's not the drum, I'll pull out that feed section and clean. Thanks


  6. #6
    Senior Tech 250+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    480
    Rep Power
    21

    Re: squeak Imagerunner advanced 400If

    Does anyone know what the code number for drum and feed section motor checks?


  7. #7
    Service Manager 2,500+ Posts
    squeak Imagerunner advanced 400If

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    2,699
    Rep Power
    41

    Re: squeak Imagerunner advanced 400If

    Quote Originally Posted by acsolutions View Post
    Does anyone know what the code number for drum and feed section motor checks?
    should be in the service manual


  8. #8
    Senior Tech 250+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    480
    Rep Power
    21

    Re: squeak Imagerunner advanced 400If

    [QUOTE=Phil B.;655545]should be in the service manual[/QUOT
    Sorry, can't afford a book right now. Just trying to get familiar with canon, it's been awhile. Thanks


  9. #9
    Service Manager 2,500+ Posts
    squeak Imagerunner advanced 400If

    Phil B.'s Avatar
    Join Date
    Jul 2016
    Location
    Raleigh NC
    Posts
    2,699
    Rep Power
    41

    Re: squeak Imagerunner advanced 400If

    [QUOTE=acsolutions;655555]
    Quote Originally Posted by Phil B. View Post
    should be in the service manual[/QUOT
    Sorry, can't afford a book right now. Just trying to get familiar with canon, it's been awhile. Thanks
    goggle it... I haven't paid for a manual in YEARS.


  10. #10
    Senior Tech 250+ Posts
    Join Date
    Jun 2010
    Location
    folsom
    Posts
    480
    Rep Power
    21

    Re: squeak Imagerunner advanced 400If

    [QUOTE=Phil B.;656251]
    Quote Originally Posted by acsolutions View Post

    goggle it... I haven't paid for a manual in YEARS.
    Ac OK thanks


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here