Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    error code: E000842-0113-05

    Please help with Canon imagepress c6000 error code: E000842-0113-05


  2. #2
    Service Manager 10,000+ Posts
    error code: E000842-0113-05

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,640
    Rep Power
    223

    Re: error code: E000842-0113-05

    [QUOTE=teckat;692994]


    E842-0113

    First check to see if the camming mechanism is working. If it is you will notice it will try to lift the belt and then fall back down.

    This is caused by pieces of the upper gears breaking off and contaminating the steel gears that lift the belt into position. Clean the gears and the problem should be resolved.

    In a few cases the problem was found to be the 53T gear on Fixing Roller End_Gear part number ,FM4-7099-000, PC figure 814 item 14.


    E842-0113

    This code refers to a pressure belt engagement error for Primary Fixing during warm-up.


    Workaround :

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched.

    Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842, 0113 code.
    The part number for PS308 is: FK2-0149-000.7

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Re: error code: E000842-0113-05

    [QUOTE=teckat;692995]
    Quote Originally Posted by teckat View Post



    E842-0113

    First check to see if the camming mechanism is working. If it is you will notice it will try to lift the belt and then fall back down.

    This is caused by pieces of the upper gears breaking off and contaminating the steel gears that lift the belt into position. Clean the gears and the problem should be resolved.

    In a few cases the problem was found to be the 53T gear on Fixing Roller End_Gear part number ,FM4-7099-000, PC figure 814 item 14.


    E842-0113

    This code refers to a pressure belt engagement error for Primary Fixing during warm-up.


    Workaround :

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched.

    Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842, 0113 code.
    The part number for PS308 is: FK2-0149-000.7
    Thanks alot for your input. The camming mechanism is working and it tried to lift the belt and then fell back down. I temporally put a piece of block under the camming mechanism to hold it up
    and the code was gone. I will go back and attempt your suggestion and keep you posted how it went. Thanks alot! however another issue came up (Paper Jam, 0A13), I will post this in a new thread for easier reference should anyone encounter similar issue.


  4. #4
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Re: error code: E000842-0113-05

    [QUOTE=teckat;692995][QUOTE=teckat;692994]


    E842-0113

    First check to see if the camming mechanism is working. If it is you will notice it will try to lift the belt and then fall back down.

    This is caused by pieces of the upper gears breaking off and contaminating the steel gears that lift the belt into position. Clean the gears and the problem should be resolved.

    In a few cases the problem was found to be the 53T gear on Fixing Roller End_Gear part number ,FM4-7099-000, PC figure 814 item 14.


    E842-0113

    This code refers to a pressure belt engagement error for Primary Fixing during warm-up.


    Workaround :

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched.

    Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842, 0113 code.
    The part number for PS308 is: FK2-0149-000.7[/QUOTE
    ...I checked the service mode, and below is a snap shot of from I/O. Please what does it mean?

    Attached Images Attached Images

  5. #5
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Re: error code: E000842-0113-05

    [QUOTE=teckat;692995]
    Quote Originally Posted by teckat View Post



    E842-0113

    First check to see if the camming mechanism is working. If it is you will notice it will try to lift the belt and then fall back down.

    This is caused by pieces of the upper gears breaking off and contaminating the steel gears that lift the belt into position. Clean the gears and the problem should be resolved.

    In a few cases the problem was found to be the 53T gear on Fixing Roller End_Gear part number ,FM4-7099-000, PC figure 814 item 14.


    E842-0113

    This code refers to a pressure belt engagement error for Primary Fixing during warm-up.


    Workaround :

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched.

    Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842, 0113 code.
    The part number for PS308 is: FK2-0149-000.7

    Hi...I checked the service mode, and below is a snap shot of from I/O. Please what does it mean?

    Attached Images Attached Images

  6. #6
    Service Manager 10,000+ Posts
    error code: E000842-0113-05

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,640
    Rep Power
    223

    Re: error code: E000842-0113-05

    The pressure belt tends to be displaced toward the shaft while driving.
    Since one-sided displacement of the pressure belt may cause damage to the fixing roller, the pressure belt position is constantly detected during driving of the pressure belt so that it is kept at the center.


    Before the pressure belt starts driving, the home position of the steering roller shaft (tilt) is detected.
    The home position is a place where the sensor flag on the swinging arm shaft blocks the light path of the Primary fixing pressure belt displacement HP sensor (PS308).


    If
    I/O P008 bit 13 stays at one there is no movement == that will result in the error E842-0113

    = No Change of state on sensor


    0: CCW( counter clockwise ) movement
    1: CW ( clockwise ) movement


    PS308.jpg

    PS308 location.jpg

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #7
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Re: error code: E000842-0113-05

    Quote Originally Posted by teckat View Post
    The pressure belt tends to be displaced toward the shaft while driving.
    Since one-sided displacement of the pressure belt may cause damage to the fixing roller, the pressure belt position is constantly detected during driving of the pressure belt so that it is kept at the center.


    Before the pressure belt starts driving, the home position of the steering roller shaft (tilt) is detected.
    The home position is a place where the sensor flag on the swinging arm shaft blocks the light path of the Primary fixing pressure belt displacement HP sensor (PS308).


    If
    I/O P008 bit 13 stays at one there is no movement == that will result in the error E842-0113

    = No Change of state on sensor


    0: CCW( counter clockwise ) movement
    1: CW ( clockwise ) movement


    PS308.jpg

    PS308 location.jpg
    Thanks a lot for your explanation and the the diagram. Two questions please: 1. I can't locate the sensor PS308 in reference to the above diagram. I've attached pics below 2. Would you recommend replacing the sensor?


  8. #8
    Service Manager 10,000+ Posts
    error code: E000842-0113-05

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,640
    Rep Power
    223

    Re: error code: E000842-0113-05

    See link for ps308 location

    Dropbox - 15341136131641956356445.jpg

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched. Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842 code

    The part number for PS308 is: FK2-0149-000.


    Last edited by teckat; 4 Days Ago at 11:44 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  9. #9
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Post Re: error code: E000842-0113-05

    Quote Originally Posted by teckat View Post
    See link for ps308 location

    Dropbox - 15341136131641956356445.jpg

    In service mode check I/O, D-Con P008, bit 13. During warm-up rotation Bit 13 should change state.
    If bit 13 does not change state this means sensor PS308 is not working or the wires going to the sensor are pinched. Check for broken wires and cut wire ties.
    In this case cutting wire ties to sensor PS308 resolved the E842 code

    The part number for PS308 is: FK2-0149-000.
    Thanks a lot for the link for ps308 location. I located the sensor, cut wire ties and checked for damamaged cables and but error stilll showing. In service mode, Bit 13 changes from 0 and remains at 1 during warm up.


  10. #10
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    17
    Rep Power
    1

    Re: error code: E000842-0113-05

    Quote Originally Posted by Kwaku01 View Post
    Thanks a lot for the link for ps308 location. I located the sensor, cut wire ties and checked for damamaged cables and but error stilll showing. In service mode, Bit 13 changes from 0 and remains at 1 during warm up.
    Assuming is the sensor PS308, could one swap with another sensor for a firm diagnos, or the pressure belt drive only works with the part number for PS308,: FK2-0149-000.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here