Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    47
    Rep Power
    1

    Desprate help with Imagepress c6000 delay jam

    Getting paper jam at UNIT B-D, just before going through the primary fixer. Delay jam...code 0112, PS200. Image attached....I've clean and swop sensors but stil getting jam. Any suggestions, please help!

    Attached Images Attached Images

  2. #2
    Service Manager 10,000+ Posts
    Desprate help with Imagepress c6000 delay jam

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,732
    Rep Power
    224

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by Kwaku01 View Post
    Getting paper jam at UNIT B-D, just before going through the primary fixer. Delay jam...code 0112, PS200. Image attached....I've clean and swop sensors but stil getting jam. Any suggestions, please help!

    0112 is a Delay jam to PS200 (Pre Fixing Feed Sensor). The paper is stopping at the Left Transport Belt assembly.


    Rotated the left transport belts by hand and they did not feel the same as the right side transport belts.

    The belts would turn easy sometimes and then get hard to turn.
    Took the drive motor (M181) off and the drive gear was loose.
    The drive gear set screws loosened up causing the drive gear to shift.
    This caused the assembly to bind.
    Put the drive gear back on and tightened the set screws.





    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    47
    Rep Power
    1

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by teckat View Post

    0112 is a Delay jam to PS200 (Pre Fixing Feed Sensor). The paper is stopping at the Left Transport Belt assembly.


    Rotated the left transport belts by hand and they did not feel the same as the right side transport belts.

    The belts would turn easy sometimes and then get hard to turn.
    Took the drive motor (M181) off and the drive gear was loose.
    The drive gear set screws loosened up causing the drive gear to shift.
    This caused the assembly to bind.
    Put the drive gear back on and tightened the set screws.



    Thanks alot for your help once again! Please which is "The drive gear set screws"?

    Attached Images Attached Images

  4. #4
    Service Manager 10,000+ Posts
    Desprate help with Imagepress c6000 delay jam

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,732
    Rep Power
    224

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by Kwaku01 View Post
    Thanks alot for your help once again! Please which is "The drive gear set screws"?


    The drive gear set screws loosened up causing the drive gear to shift.

    check on back of the motor


    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    47
    Rep Power
    1

    Thumbs up Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by teckat View Post


    The drive gear set screws loosened up causing the drive gear to shift.

    check on back of the motor
    You legend! It worked. Thanks heaps!!!


  6. #6
    Service Manager 10,000+ Posts
    Desprate help with Imagepress c6000 delay jam

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,732
    Rep Power
    224

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by Kwaku01 View Post
    You legend! It worked. Thanks heaps!!!

    Macgyver.jpgwelcome

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #7
    Technician
    Join Date
    Aug 2018
    Location
    NSW
    Posts
    47
    Rep Power
    1

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by teckat View Post
    I bought canon imagepress c6000 secondhand, after installation, I keep getting error after errors. The new errow is, E110-0201. I've no clue how to go about this one...any help will be greatful!


  8. #8
    Service Manager 10,000+ Posts
    Desprate help with Imagepress c6000 delay jam

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,732
    Rep Power
    224

    Re: Desprate help with Imagepress c6000 delay jam

    Quote Originally Posted by Kwaku01 View Post
    I bought canon imagepress c6000 secondhand, after installation, I keep getting error after errors. The new errow is, E110-0201. I've no clue how to go about this one...any help will be greatful!

    E110-0201 = Magenta laser
    For trouble shooting purposes swapp J1112 (yellow laser scanner power cable) and J1122 (magenta laser scanner power cable) on DC-CON 1-3

    see if error code moves to Yellow
    (E110-0101)----------if error switches---most likely DC-Controller 1-3 (FM2-7687-000) not supplying power to connector

    ============================or

    E110-0201 points to the Magenta laser scanner motor that does not reach a certain speed within a specified period.






    In this case, checking the connection of the magenta video cable, swapping the magenta laser unit, performing DCON clear and clearing the error code in service mode did not change the symptom.






    In this case, replacing the DC controller PCB 1-3 (UN240) resolved error code in the field. DC controller PCB 1-3 Assembly FM2-7687-000








    E061-0291

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here