Good day all,
Just to start off, I am more of a computer repair/network tech, and obviously not so much of a copier tech. I follow instructions pretty well
I have just acquired an iR2200 with an error code of E000000-0000. I assumed it wouldn't be much of a problem since the previous owner said that it was working perfectly fine prior to moving the unit down the hall to make room for their new copier. When they plugged it in to get a copy count a week later it came up with this error. I've got the service handbook which has been handy, but I am still unable to pin point exactly what it needs. Here is what I have done so far:
1. Clear the error - The unit will come up fine if I start it up with the front door open getting the front door open message of course. When I close the door it will display the main screen for 2 seconds then give the error message.
2. Checked all connectors between main power supply PCB (J8) and heater. Check all connectors between DC controller PCB (J320) and Thermistor. Everything checked good. Disconnected and reconnected connectors.
3. Checked continuity between pins 1 & 2 and 3 & 4. Pins 1 &2 metered 1.5 M ohm, and pins 3 & 4 metered 400 k ohm.
Also I have noticed that when I turn the power on I can hear a faint "siren" when I have the developer unit in...as soon as I pull it out, the "siren" stops. When in Service Mode, going to Copier > Function > Install > Toner-S, I get "Check the Developer" message.
I hope this was detailed enough for someone to give me some guidance. Any and all help will be greatly appreciated.
Just to start off, I am more of a computer repair/network tech, and obviously not so much of a copier tech. I follow instructions pretty well
I have just acquired an iR2200 with an error code of E000000-0000. I assumed it wouldn't be much of a problem since the previous owner said that it was working perfectly fine prior to moving the unit down the hall to make room for their new copier. When they plugged it in to get a copy count a week later it came up with this error. I've got the service handbook which has been handy, but I am still unable to pin point exactly what it needs. Here is what I have done so far:
1. Clear the error - The unit will come up fine if I start it up with the front door open getting the front door open message of course. When I close the door it will display the main screen for 2 seconds then give the error message.
2. Checked all connectors between main power supply PCB (J8) and heater. Check all connectors between DC controller PCB (J320) and Thermistor. Everything checked good. Disconnected and reconnected connectors.
3. Checked continuity between pins 1 & 2 and 3 & 4. Pins 1 &2 metered 1.5 M ohm, and pins 3 & 4 metered 400 k ohm.
Also I have noticed that when I turn the power on I can hear a faint "siren" when I have the developer unit in...as soon as I pull it out, the "siren" stops. When in Service Mode, going to Copier > Function > Install > Toner-S, I get "Check the Developer" message.
I hope this was detailed enough for someone to give me some guidance. Any and all help will be greatly appreciated.
), I've been doing that since childhood. I've already taken the entire Fuser unit apart and put it back together. Even took apart a fuser unit from an HP 5000 (just to see if I could scrounge something to make mine work...no go). As sad as this may sound, to have something that I can take apart and possibly fix myself for little to no money is what I do for fun on a Friday night...as my girlfriend laughs at me. I'm just going to buy the FF assy. and see where this goes. By the way, does anyone have a SM to help me out here. I'm not so sure I would have much to offer in trade...not even cash as I am currently unemployed. My email is zerocool9897 AT sbcglobal DOT com. Oh oh oh, about the "check the developer" thing i mentioned before...should I be concerned about that at all?
Comment