ir2200

[D_L_P]

	Quote:			Originally Posted by bomberi
	if a take the boot, or the rui to download they go well

Now I think it sounds like just your ir2200 system file is corrupt. The latest version is 45.01 and looking at my C:\servtool\ir2200\system its 26.5 mb in size. I suppose its possible if you downloaded it for the boot and rui to be fine but the system got corrupt. Get a new copy of the system software.
If you can connect to the copier with SST I'd eliminate your cable or port settings.

[ymmtech]

There are some method to check corrupted file, for example, 2200 system: It is at c:\servicetool\ir2200\system\usenv4501\ir2200-usen4501-5af7.prg.
The 5AF7 is 16 bit check sum of file ir2200-usen4501-5af7.prg.
Use disk utilities tool to open prg file, calculate its 16 bit check sum will get 5AF7. The same method can apply to any others prg files.

[bomberi]

somes knews for my pc. The port is (com,lpt1) ecp mode but i see the bi-centronic port is ieee1394 not ieee1284. Can my pc work with the bi-centronic ieee1394? THANKS

[mrfixit51]

	Quote:			Originally Posted by bomberi
	somes knews for my pc. The port is (com,lpt1) ecp mode but i see the bi-centronic port is ieee1394 not ieee1284. Can my pc work with the bi-centronic ieee1394? THANKS

ieee1394 is pertaining to your Firewire port, and it cannot be utilyzed for SST.

[ymmtech]

Some note book share the RJ45 connector. It can function as a LAN or an IEEE1394.
My dear friends, comming up more terms to know. C boot ROM, Nboot ROM, IP ....

[D_L_P]

	Quote:			Originally Posted by bomberi
	My problem is the hd and i have adapt a toshiba hd. I have format it with the hd format and its ok. Now if I want to download the system it go well and the machin make downloading in the screen, after a mn it make error: the check sun did not match, the data may have suffered loss/damage while beeing transmitted, check the conexion between the pc and the machin. I try again and it make swithing to the ecp mode has failled. my hdd is a new( toshiba mk4026gax). I've traying to reinstall the sst and begin the way, the same error appear now i want to change a laptop to try again. I have cange pc and the sst but always the same error is hear I think it is the system so if someone can send me I will try again. I have formating the hdd, now i am the step to download the system and when i begen to download there are some error when data is beeing transfered but when i take the boot to transfer it go well and the system is the first to be transfered one by one. I try at least 5 hdd and i have the same error. Because I have 4 ir2200, 3300 with same error of hdd. I ve taking another hhd with is good and i try to download and it do the same error the system can not download but i win to format the hdd. Ithink that the system is not good. The file is 1,5 MO I use parallel cable now i want to now if my system capacity 1,5mo is ok. So i want to be sure that the system is good. i use bicentronic cable and the sst show that. The thing i don't undestand, is why have i succes to format the hdd or when i try to download the boot it go well? Is this possible when the cable config is failled? The system to download first can not go when i take one by one but if a take the boot, or the rui to download they go well at the end the machine show that data is writting now don't cut power. The machine error is E602-01. After succed to format the hdd, the error became E602-02.

Ok just to review, your problems are: 1.You have a Non compliant HDD 2.Check sum error 3. E602

You have tried: 1.Reinstall SST 2.Change PC 3.Other HDD 4.Using parallel cable now

I think problem #1 is resolved, you must have followed those instructions for adding the HDD model number, because you are able to format the HDD. As for problem #2, your file is 1.5MB when it should be 26.5 MB. Get a new good copy of the ir2200 firmware. I think the 602 codes are just another symptom of the bad (1.5MB) system file.

Just to cover even more ground, to get my IBM thinkpad with WinXP to work with SST and a parallel cable I had to:
1. Enable legacy Plug and Play detection.
2. Enable using any interrupt assigned to the port.
3. Change operating mode to ECP.
This was done in the device manager, propeties of the parallel port.

[Peter Sim]

	Quote:			Originally Posted by bomberi
	Thank you; can i know how to set the ecp mode. i use bicentronic cable and the sst show that. The thing i don't undestand, is why have i succes to format the hdd or when i try to download the boot it go well? Is this possible when the cable config is failled? The system to download first can not go when i take one by one but if a take the boot, or the rui to download they go well at the end the machine show that data is writting now don't cut power. The machine error is E602-01. After succed to format the hdd, the error became E602-02.

After you successfuly format your HDD,you need to know your boot rom version,if is N version,you only need to download 2200N>"System" firmware into your HDD.

[bomberi]

my thanks to all, my problem is now ended. It's the system 1,5mo not 26,5mo i have done a knew copy and is ok. THANK YOU

[mrfixit51]

	Quote:			Originally Posted by bomberi
	my thanks to all, my problem is now ended. It's the system 1,5mo not 26,5mo i have done a knew copy and is ok. THANK YOU

Glad you resolved it! Thanks for the feedback to the group...

[D_L_P]

Ditto.

MrFixit I just saw where you are from. If you work for a Canon dealership I think I know which one (if it's not Ikon), and a very good one at that.