Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 9 of 9
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Oct 2008
    Location
    Sarajevo
    Posts
    60
    Rep Power
    0

    CLC 1110 Error code E071-0001 and E071-F000

    Dear Experts,
    I have a CLC 1110 copier machine which make till now about 95000 copy and still look as new.
    The problem is I have an error codes E071-0001 and E071-F000, and sometimes shows jammed paper on the TD (but no paper is jammed). I called a certificated service men they try a lot of variants to eliminate the errors, they replace the TD, replace the motor of the TD lifters and replace the motor of TD polisher, but without a result, they replace the DC controller even replace the electronic card of the TD and polisher lifter, also they replace the all base where the TD and fixing unit are lay, they clean and test all the sensors but without a result, they even take parts of my machine and try it on their machines and my parts work perfectly.
    The problem also is the motor of the polish lifter does not lift the polisher at all on my machine even if it is ok and worked on other machines, and at this point my machine report error and even if the process of polishing pass which is in my case is rare, first copy stuck in the TD and again the error code appear again
    Four service firm try to fix it but without a result.
    Please you are my last chance and please consider that any information will help me

    Please if any information or details needed, feel free to message me.
    Thank you a lot

  2. #2
    Trusted Tech 50+ Posts
    Join Date
    Nov 2009
    Posts
    93
    Rep Power
    30
    Hi,

    Not Trained but can only find info below.

    E071 / E072 / E073

    Transfer Frame Connector
    Poor Contact due to toner scattering around Transfer Connector
    Replace Connector FG6 0948

    TD Cleaner assy
    Motor M8 being overloaded. Drive shaft from motor goes through long plastic bearings these were getting clogged with toner and oil
    clean drive shafts
    Transfer driver PCB
    Static discharge onto transfer driver from peeling off old TD sheet too fast
    Replace Transfer Driver PCB (FG6 - 2579) Remove old TD sheet SLOWLY to prevent problem.

    Good Luck

    Shazza

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Oct 2008
    Location
    Sarajevo
    Posts
    60
    Rep Power
    0
    Quote Originally Posted by shazza View Post
    Hi,

    Not Trained but can only find info below.

    E071 / E072 / E073

    Transfer Frame Connector
    Poor Contact due to toner scattering around Transfer Connector
    Replace Connector FG6 0948

    TD Cleaner assy
    Motor M8 being overloaded. Drive shaft from motor goes through long plastic bearings these were getting clogged with toner and oil
    clean drive shafts
    Transfer driver PCB
    Static discharge onto transfer driver from peeling off old TD sheet too fast
    Replace Transfer Driver PCB (FG6 - 2579) Remove old TD sheet SLOWLY to prevent problem.

    Good Luck

    Shazza


    thank you Shazza, I will try this.

    Guys any other ideas???

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Oct 2008
    Location
    Sarajevo
    Posts
    60
    Rep Power
    0
    nothing is solved.

    I also check the fuse pcb and it is ok

    please help

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Oct 2008
    Location
    Sarajevo
    Posts
    60
    Rep Power
    0

    E071-F000 error code

    Where is the Experts.

    The machine now just generate E071-F000 error code

  6. #6
    Senior Tech 100+ Posts Van Steal's Avatar
    Join Date
    Apr 2008
    Location
    Dublin
    Posts
    177
    Rep Power
    34
    Eo71 is for the A B C side senors in the front of the T/D ass'y can detect home postion. There is a black plate on the front insde of the t/d that can get dirty or crack. Also the the sensors can go faulty. But if the tech changed the hole ass'y then it rules that out

  7. #7
    Trusted Tech 50+ Posts
    Join Date
    Oct 2008
    Location
    Sarajevo
    Posts
    60
    Rep Power
    0

    Unhappy confused

    so what to do.

    experts help me please.

    can I write to Canon directly for this, are they will help me.


    please help

  8. #8
    Technician
    CLC 1110 Error code E071-0001 and E071-F000


    Join Date
    Nov 2009
    Posts
    41
    Rep Power
    30
    Question I have is if you cheat the front doors does the transfer drum lift up against the photosensitive drum and spin? If that is fine I would be looking at the transfer drawer connectors in both the transfer frame (part.# FG3-2592-000) and on the rear frame of the machine (part# FG6-0948-000) I have replaced many of these harnesses for various E071 codes.

  9. #9
    Senior Tech 100+ Posts ricardobres's Avatar
    Join Date
    Apr 2008
    Location
    Curitiba
    Posts
    147
    Rep Power
    34
    Hi. Did you check the front door interlock? And the bearing of the polish motor assembly? It goes out of place.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here