Canon Imagepress C1

[irtek]

I'm working on an IPR C1 and it has some white spots in the halftones. The machine just in from a wholesaler with 98k on it, but I can't be sure parts were not swapped. I isolated it to the transfer belt and pulled the ITB unit. There are spots on the transfer belt that match the spots on the copies. They look like pinholes in the belt, not visable holes but like HV arc to the belt. Is this a common problem on this machine? Is there anything I can do to prevent this from happening again? Thanks for any input on this problem.

[SCREWTAPE]

Its wear and tear. The belt lasts about 70K. This is a high maintenance machine. But it got some good copy qaulity.

[irtek]

Thanks for the information. I was thinking I had read where the belt was rated at 300k but I went back and checked and it is rated for 75K, my bad. thanks for the help.

[irtek]

Is FL2-2576 the correct part # for the transfer belt? Anyone have the part # for the QA kits and what is in the kits? Thanks.

[charm5496]

Yes that is the correct part number for the ITB belt.
The kit numbers are F02-5811-000, F02-5812-000, F02-5813-020
I am not going to type what each one has in them, but we do not use them because of some the useless parts they have in them.

[irtek]

Thanks. My parts supplier said the ITB# has changed to FL2-2584.

[wtroll]

Hi,
if you check the related counters of consumables in SERVICE MODE/COUNTERS, you may have the correct situation of any parts and the % of work.
Don't forget to clear the related counter when you change a part.

[teckat]

I'm working on an IPR C1 and it has some white spots in the halftones. The machine just in from a wholesaler with 98k on it, but I can't be sure parts were not swapped. I isolated it to the transfer belt and pulled the ITB unit. There are spots on the transfer belt that match the spots on the copies. They look like pinholes in the belt, not visable holes but like HV arc to the belt. Is this a common problem on this machine? Is there anything I can do to prevent this from happening again? Thanks for any input on this problem.

The pit marks are from the arching of the transfer roller to the belt./replace the belt & roller/ clean interior
this is a high maintenance machine/ u need to set up a PM service sch.on these.imagePRESS

imagePRESS C1
250K QA Kit
F02-5813-020

Part Number Description QTY
FM2-2496-000 Primary Charging Assembly
FM2-2495-000 Pre-transfer Charging Assembly
FC7-0957-000 Ozone Filter (Right)
FL2-0439-000 Air Filter
FC6-1392-000 Ozone Filter (Left)
FC7-0958-000 Toner Filter (Right)
FC6-9817-000 Toner Filter (Left)
FC6-9829-000 Toner Filter (Rear)
FC8-8816-000 Air Filter 1
FC8-8817-000 Air Filter 2
FC8-8818-000 Air Filter 3
FC7-0932-000 External Heating Roller
FC5-2524-000 Cassette Pick-up Roller
FC5-1661-000 Secondary Transfer Inside Roller



C1 100K QA Kit
F02-5812-010

Part Number Description QTY
FM2-8070-010 Secondary Transfer Cleaner Unit
FC5-8829-000 Cleaning Blade
FL2-2707-010 Seal Support Plate (Front)
FL2-2708-010 Seal Support Plate (Rear)
FL2-2709-000 Scoop-up Sheet Support plate
FL2-2713-000 End Seal (Front)
FL2-2714-000 End Seal Rear)
FC5-8837-000 Drum Cleaning Brush
FL2-6530-000 Fixing Belt
FM3-1217-000 Pressure Pad Assembly
FL2-2788-010 Pad Cover
FC5-9778-000 Fixing Cleaning Belt
FL2-5453-000 Oil-coating Roller
FC5-9777-000 External Heating Roller Cleaner
FC5-9766-000 Steering Roller
FL2-6048-000 Refresh Roller
FC7-0175-000 Refresh Heat Insulating Bushing



25K QA Kit
F02-5811-000
Part Number Description QTY
FC6-1056-000 Primary Grid Plate
FL2-2720-000 Pad Holder (Primary)
FL2-0462-020 Slider (Primary)
FL2-2720-000 Separation Roller (Manual Feed Tray)
FL2-0462-020 Slider (Pre-transfer)



Air Filter 4 (FC6-3482-000) was eliminated from the 250K Kit because the Duct Assembly was eliminated
from the imagePRESS C1/C1+