Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 5 of 5
  1. #1
    Senior Tech 1,000+ Posts kuby's Avatar
    Join Date
    Oct 2007
    Location
    Texas
    Posts
    1,269
    Rep Power
    54

    Canon ir 3035 - E540-8005

    Problem with the S1 finisher. The tray does not go up and down. And it gives a Unable to use finisher error. Did not find anything in the manual about testing the functions of the finisher. Is there a way to test the motors, sensors, and clutch functions of the finisher?

    Has anyone run into this error before?

    Thanks

    Ronald

  2. #2
    East Coast Imaging 2,500+ Posts
    Canon ir 3035 - E540-8005

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,399
    Rep Power
    69
    If you have functions limited enable you will lose finisher options. I never see to many 540's with S1's so i never had to check. But if you go into Additional Functions > Common settings > screen 5 and check if Limited Functions is On. If it is on, then turn Limited Functions Off and power cycle the copier. This might work if you have this option. Most image runners have this option if you know. If the error pops again, check fuses on the finisher PCB.
    Last edited by SCREWTAPE; 01-22-2010 at 02:16 AM.
    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  3. #3
    Lead Service Technician 1,000+ Posts mrfixit51's Avatar
    Join Date
    Oct 2008
    Location
    Clinton, Iowa
    Posts
    1,976
    Rep Power
    54
    E540.jpg

    for enlightenment...

    The cables that follow the tray have been known to get caught, not allowing the tray
    to travel full distances...

  4. #4
    Technician
    Join Date
    May 2009
    Location
    Johannesberg
    Posts
    13
    Rep Power
    31
    Check the fuses on the finisher controller. There are about seven on the board.

  5. #5
    Service Manager 10,000+ Posts
    Canon ir 3035 - E540-8005

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    i agree/w mrfixit51=first check that cable harness !!
    also check or replace "paper face sensing flag" if old it is narrow / replace w/new type=it's face has been enlarged to block more area of sensor light, new part #4A3-1043-020 & stopper damper #4Y3-3006-000

    *or For various Finisher error codes and malfunctions:
    With the copier "ON' turn ON all 4 dip switches, cheat the finisher door switch, press and hold SW2 until the LED stops flashing. Then turn off copier, turn off dip switches and turn copier back on. Check to see if the finisher initializes and if the problem is resolved.

    If all fails Check FU3 for 24v on both side of the fuse= from ground to one side /then ground to the other side /both need to read 24v, if one side does not read 24v - fuse is blown, replace the finisher controller. Part number 4G1-1478-050.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here