Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 18
  1. #1
    Technician
    Join Date
    Sep 2008
    Location
    Kent, WA
    Posts
    20
    Rep Power
    19

    ir1023 - Unable to get to Webinterface

    I am having an issue getting to a customers UI on their ir1023. I tried Mozilla firefox and it worked for a few minutes and then just timed out like Internet Explorer(Http 400 bad request) error comes back on IE.

    I checke to make sure the Remote UI feature was turned on and rebooted the copier a few times, and still same result.

    Has anyone had an experience with this. I was scanning through the Canon Esupport site, and still have not found anything yet.

    The customer said they have had this issue for almost a year, so we updated firmware and still not avial.

    Sean


  2. #2
    Field Supervisor 500+ Posts
    Join Date
    Nov 2007
    Location
    New Jersey
    Posts
    575
    Rep Power
    28
    Set the RUI to On, under Additional Functions, System Settings, Remote UI. (make sure that HTTP is also enable and no IP address ranges are set for HTTP access)


  3. #3
    Service Manager 10,000+ Posts
    ir1023 - Unable to get to Webinterface

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,155
    Rep Power
    213
    Correct version of RUI firmware must be flashed onto the copier. A specific version of the RUI firmware is required for each individual version of system software.

    Flash the copier with the correct version of RUI firmware. with User Support Tool

    Be sure to enable HTTP and RUI on the copier.
    Be sure to enable "Dedicated Port" on the copier.

    Type in IP address of the imageRUNNER in the browser address bar.

    When one of the Dept. ID, SDL, or SSO authentication functions is enabled on the copier the RUI is also restricted to authorized users

    MEAP Enabled Devices, please make sure that the proper MEAP version in Service Mode/Copier/Display/Version is also installed. If everything fails, perform a Clear MMI. Also note that on MEAP enabled devices, USE HTTP under TCP/IP Settings and USE HTTP under MEAP Settings must be ON.


  4. #4
    Technician
    Join Date
    Sep 2008
    Location
    Kent, WA
    Posts
    20
    Rep Power
    19
    Thanks folks, I will test these out. I was going to do a wipe and reset to bring back to factory defaults, but I will do all suggestions as well.


  5. #5
    Lead Service Technician 1,000+ Posts mrfixit51's Avatar
    Join Date
    Oct 2008
    Location
    Davenport, Iowa
    Posts
    1,979
    Rep Power
    40
    A clean install of complete system software package should resolve it...


  6. #6
    East Coast Imaging 2,500+ Posts
    ir1023 - Unable to get to Webinterface

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,402
    Rep Power
    57
    Have you tried pinging the 1023 to verified that your network connection is okay? Just a thought.

    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  7. #7
    Technician
    Join Date
    Sep 2008
    Location
    Kent, WA
    Posts
    20
    Rep Power
    19
    Quote Originally Posted by SCREWTAPE View Post
    Have you tried pinging the 1023 to verified that your network connection is okay? Just a thought.
    Yes the copier has responded to pings, and it prints out just fine.

    The problem is the webinterface does not come up in IE. It works for a few seconds on Firefox, but then it also loses it afterwards.

    We are going to do an update first and move from there.

    Thanks for all those who have helped.

    Sean


  8. #8
    East Coast Imaging 2,500+ Posts
    ir1023 - Unable to get to Webinterface

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,402
    Rep Power
    57
    Have you connected directly to the 1023 with a laptop.

    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  9. #9
    Technician vidarb's Avatar
    Join Date
    Mar 2010
    Location
    Norway
    Posts
    25
    Rep Power
    16
    I am also having this problem, and the customer can not scan. Print works fine. Will try to upgrade today and see what happens.


  10. #10
    Technician vidarb's Avatar
    Join Date
    Mar 2010
    Location
    Norway
    Posts
    25
    Rep Power
    16
    Haha, loaded software v.63.01 with SSt 4.23.
    Everything was going as planned.
    Powered of and on the machine and it bricked!
    Dont know what went wrong but now i probably need to replace the image processor PCB.

    Even a broken clock is right twice a day.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here