Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Technician Dimacop's Avatar
    Join Date
    Apr 2009
    Location
    new jersey
    Posts
    43
    Rep Power
    21

    Smile firmware ir7105/7086

    I have the firmware for ir7105/7086
    more upgraded the machine with the rcon iR7095
    and gave the system error
    the machine does not load and the e732-000
    seem to have to have rcon of ir7086 I have dcon
    if someone has the rcon please send me

    Thank you and good luck

    Roberto

    betinho23@terra.com.br

  2. #2
    Service Manager 10,000+ Posts
    firmware ir7105/7086

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,847
    Rep Power
    229
    how did new jersey end up in Brasil'

  3. #3
    Technician Dimacop's Avatar
    Join Date
    Apr 2009
    Location
    new jersey
    Posts
    43
    Rep Power
    21
    I travel a lot to stay in new york friends in new jersey when I'm in Brazil
    because I have several machines here.
    hope that answers your doubt

    you have the rcon this machine
    I need her so much

    Thank you and good luck

  4. #4
    Service Manager 10,000+ Posts
    firmware ir7105/7086

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,847
    Rep Power
    229
    Quote Originally Posted by Dimacop View Post
    I travel a lot to stay in new york friends in new jersey when I'm in Brazil
    because I have several machines here.
    hope that answers your doubt

    you have the rcon this machine
    I need her so much
    Thank you and good luck
    imageRUNNER 7105/7095/V2- 7086 V2/-7105P V2=v80.02 SST has all the latest firmware for these models

    for the New Flash ROM, Canon USA is advising to
    upgrade to RCON v3.01 or higher (iR7105/7095), RCON v4.02 or higher
    (iR7086), Finisher-V1/V2 or higher v22.01 (Stacker), High Capacity Stacker-A1

    Special BootROM v10.99 has an issue where it is not displayed on the Service Support Tool when
    upgrading from iR7105 to an iR7105 V2 series.
    Using “ASSIST MODE” or upgrading using a “USB FLASH DRIVE” will upgrade the iR7105
    BootROM to an iR7105 V2 BootROM.
    v14.01 or higher (OP_CONT), and Perfect Binder-A1 v11.01 or higher
    (OP_CONT) to avoid any future issues.


    When installing System Software v55.05 or higher on the older imageRUNNER 7086/ 7105/ 7095/
    7095 Printer, please follow the procedure below to insure proper installation or an error will occur.


    **When installing System Software onto imageRUNNER 7086/ 7095/ 7105/ 7095 Printer copiers lower than
    v55.05, the following important steps must be followed:
    1. Place the machine in Download Mode by holding down 2 & 8 and powering ON the main switch.
    2. Using the Service Support Tool v4.22Et, check the “Special Box” at the top left.
    3. Select “iR7105” Folder/ “SINGLE” and install “Special BootROM v10.99”.
    4. Turn OFF the Machine and then back ON holding 2 & 8 to place back into Download Mode
    Once the BootROM is rewritten, it cannot be returned to the old model version.
    5. Using the Service Support Tool v4.22Et, select iR7105_V2 and perform an “ALL PARTIONS” HDFORMAT
    to the Hard Disk Drive [HDD].
    6. Select “ALL” to install System Software v55.05 or higher.
    7. Power OFF & ON Machine. The machine will extract and install the system software.
    8. When installation is completed, turn OFF, then ON holding down 1 & 7 to place into “FIXED IP”
    Download Mode.
    9. Select iR7105_V2 and select “SINGLE” to install the Accessories.
    Note:
    After flashing the accessories firmware by way of an ARCNET connection, be sure to select the
    “SHUTDOWN” button on the Service Support Tool or the accessories will not upgrade. Pressing the
    Shutdown will place the 7086/ 7105/ 7096/ 7105 printer into a pre-shutdown mode.

    if the error is on a imageRUNNER 7095P=E732 pertains to a communication fault between Reader Controller pcb and the Main Controller pcb. The imageRUNNER 7095P is a network printer model which has no Reader unit / Document Feeder, therefore the imageRUNNER 7095P has no Reader Controller pcb.
    Just re flash system software

  5. #5
    East Coast Imaging 2,500+ Posts
    firmware ir7105/7086

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,401
    Rep Power
    61
    Quote Originally Posted by ticket View Post
    imageRUNNER 7105/7095/V2- 7086 V2/-7105P V2=v80.02 SST has all the latest firmware for these models

    for the New Flash ROM, Canon USA is advising to
    upgrade to RCON v3.01 or higher (iR7105/7095), RCON v4.02 or higher
    (iR7086), Finisher-V1/V2 or higher v22.01 (Stacker), High Capacity Stacker-A1

    Special BootROM v10.99 has an issue where it is not displayed on the Service Support Tool when
    upgrading from iR7105 to an iR7105 V2 series.
    Using “ASSIST MODE” or upgrading using a “USB FLASH DRIVE” will upgrade the iR7105
    BootROM to an iR7105 V2 BootROM.
    v14.01 or higher (OP_CONT), and Perfect Binder-A1 v11.01 or higher
    (OP_CONT) to avoid any future issues.


    When installing System Software v55.05 or higher on the older imageRUNNER 7086/ 7105/ 7095/
    7095 Printer, please follow the procedure below to insure proper installation or an error will occur.


    **When installing System Software onto imageRUNNER 7086/ 7095/ 7105/ 7095 Printer copiers lower than
    v55.05, the following important steps must be followed:
    1. Place the machine in Download Mode by holding down 2 & 8 and powering ON the main switch.
    2. Using the Service Support Tool v4.22Et, check the “Special Box” at the top left.
    3. Select “iR7105” Folder/ “SINGLE” and install “Special BootROM v10.99”.
    4. Turn OFF the Machine and then back ON holding 2 & 8 to place back into Download Mode
    Once the BootROM is rewritten, it cannot be returned to the old model version.
    5. Using the Service Support Tool v4.22Et, select iR7105_V2 and perform an “ALL PARTIONS” HDFORMAT
    to the Hard Disk Drive [HDD].
    6. Select “ALL” to install System Software v55.05 or higher.
    7. Power OFF & ON Machine. The machine will extract and install the system software.
    8. When installation is completed, turn OFF, then ON holding down 1 & 7 to place into “FIXED IP”
    Download Mode.
    9. Select iR7105_V2 and select “SINGLE” to install the Accessories.
    Note:
    After flashing the accessories firmware by way of an ARCNET connection, be sure to select the
    “SHUTDOWN” button on the Service Support Tool or the accessories will not upgrade. Pressing the
    Shutdown will place the 7086/ 7105/ 7096/ 7105 printer into a pre-shutdown mode.

    if the error is on a imageRUNNER 7095P=E732 pertains to a communication fault between Reader Controller pcb and the Main Controller pcb. The imageRUNNER 7095P is a network printer model which has no Reader unit / Document Feeder, therefore the imageRUNNER 7095P has no Reader Controller pcb.
    Just re flash system software
    This V2 upgrade must be done correctly to the tee!!
    If not It will resort to E602. Its not your ordinary upgrade.
    Every instruction must be follow by its order of procedure.
    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  6. #6
    Lead Service Technician 1,000+ Posts mrfixit51's Avatar
    Join Date
    Oct 2008
    Location
    Davenport, Iowa
    Posts
    1,973
    Rep Power
    43
    Quote Originally Posted by SCREWTAPE View Post
    This V2 upgrade must be done correctly to the tee!!
    If not It will resort to E602. Its not your ordinary upgrade.
    Every instruction must be follow by its order of procedure.
    I agree with that statement, mostly true,, but it is interesting in that they advise you to format the hard drive after the first bootrom updating, then use the ALL batch file to install the software. The ALL batchfile requires you to boot the copier into fixip mode first, but this is impossible since there is no system to boot up with since you just formatted the hard drive. You need to use the ALL_HDF batch file instead.... the rest of the procedure is correct though.

  7. #7
    Junior Member
    Join Date
    Oct 2008
    Location
    Skopje
    Posts
    4
    Rep Power
    0

    Re: firmware ir7105/7086

    I need firmware for ir7105

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here