Page 9 of 10 FirstFirst 12345678910 LastLast
Results 81 to 90 of 94
  1. #81
    Junior Member
    Join Date
    Jun 2016
    Location
    Berlin
    Posts
    8
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    did you have this specific manual for iPF605?. I have only a service manual iPF6000 series, but there I can't find voltages for the sensors.

  2. #82
    Junior Member
    Join Date
    Jun 2016
    Location
    Berlin
    Posts
    8
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    when I'm going to service mode, the same error comes (E196-404E)!
    I can't enter the service mode to reset the error....


    update: The voltage at sensor is too low. It must be 3.3V there are only 1V. Measuring at the power supply and the two voltages there comes out, are also tooo small....must see...
    Last edited by Netti14; 06-25-2016 at 12:24 AM.

  3. #83
    Service Manager 10,000+ Posts
    imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Check for a change of state for sensor.

    Sensor has three leggs.
    Ground, Signal Change, Supply
    Best to check Signal change output in connector from board, & not across load (photo sensor itself)
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #84
    Service Manager 10,000+ Posts
    imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    may need to change that Main Controller
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #85
    Junior Member
    Join Date
    Jun 2016
    Location
    Berlin
    Posts
    8
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Quote Originally Posted by teckat View Post
    may need to change that Main Controller

    I think, it's the best way! Too many error's....

  6. #86
    Junior Member
    Join Date
    Jun 2016
    Posts
    5
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    G'day,

    My canon IPF8100 printer was working perfectly until I recently upgraded the firmware.

    Since then it is throwing massive errors in relation to the heads.
    I have noticed this is a common issue with the new firmware and many have solved the problem by downgrading to firmware 1.34
    Unfortunately, I cannot find this firmware anywhere as Canon has deleted all of it's old firmware

    If anyone could please direct me on where I could access firmware 1.34 or any other possible solution it would be greatly appreciated.

    This has cost me 4 business days already and I am very eager to get this printer working again.

    Thanks in advance,

  7. #87
    Service Manager 10,000+ Posts
    imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Quote Originally Posted by jayskee View Post
    G'day,

    My canon IPF8100 printer was working perfectly until I recently upgraded the firmware.

    Since then it is throwing massive errors in relation to the heads.
    I have noticed this is a common issue with the new firmware and many have solved the problem by downgrading to firmware 1.34
    Unfortunately, I cannot find this firmware anywhere as Canon has deleted all of it's old firmware

    If anyone could please direct me on where I could access firmware 1.34 or any other possible solution it would be greatly appreciated.

    This has cost me 4 business days already and I am very eager to get this printer working again.

    Thanks in advance,



    https://www.usa.canon.com/internet/p...B0AMD0F1Q42K25
    ver. 1.43 is here
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #88
    Junior Member
    Join Date
    Jun 2016
    Posts
    5
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Quote Originally Posted by teckat View Post
    Thank you for this, I am well aware.. 1.43 is what has caused this issue in the first place, I need to downgrade

    Please refer to my thread: Canon IPF 8100 - Firmware downgrade

    Or PM If possible

    Thank you!

  9. #89
    Junior Member
    Join Date
    Nov 2016
    Location
    California
    Posts
    3
    Rep Power
    0

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Hello
    I too have a Canon iPF605 with the ever-present "Close Upper Cover" message (and of course it is closed).
    I also fear that the inevitable end will be to replace the main board. But until then, I have endlessly been researching my options.
    In my effort to try the L Printer Service tool (V 1.50) to update the firmware (Service mode does not work/am able to get it to Download Mode) I can only get as far as the "Setup" step for which it says that my operating system is not supported. This is not true as I have the correct FUT/Firmware/OS and have tried them on multiple computers but yet it still will not budge.

    So does anyone have any advice on these two subjects?
    1) What to do about the operating system fault? (Is there another version that I could use? I have multiple different operating systems including Windows 7 64/Vista/Mac)
    2) Should this not work, could it be my cover switch voltage?/What would be the best route to fixing it?

    Thanks so much!

  10. #90
    Service Manager 10,000+ Posts
    imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagePROGRAF L Printer Service Tool (Ver. 1.40)_ New

    Quote Originally Posted by letstrythisagain View Post
    Hello
    I too have a Canon iPF605 with the ever-present "Close Upper Cover" message (and of course it is closed).
    I also fear that the inevitable end will be to replace the main board. But until then, I have endlessly been researching my options.
    In my effort to try the L Printer Service tool (V 1.50) to update the firmware (Service mode does not work/am able to get it to Download Mode) I can only get as far as the "Setup" step for which it says that my operating system is not supported. This is not true as I have the correct FUT/Firmware/OS and have tried them on multiple computers but yet it still will not budge.

    So does anyone have any advice on these two subjects?
    1) What to do about the operating system fault? (Is there another version that I could use? I have multiple different operating systems including Windows 7 64/Vista/Mac)
    2) Should this not work, could it be my cover switch voltage?/What would be the best route to fixing it?

    Thanks so much!
    ============================================
    are u connected with a Crossover Cable

    are you using the 32bit or 64bit L Printer Tool
    see attachments---------------------------------------------

    https://www.dropbox.com/s/5l89nl9iph5cnwi/L%20Printer%20Tool___1.80%20Info.pdf?dl=0

    https://www.usa.canon.com/internet/portal/us/home/support/details/printers/support-imageprograf-printers/imageprograf-ipf605


    Attached Files Attached Files
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here