Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    Senior Tech 250+ Posts ReproKev's Avatar
    Join Date
    Feb 2009
    Location
    Newark, DE
    Posts
    256
    Rep Power
    35

    Part # for attachment sensor arm for puncher unit AH1

    I have a puncher unit AH1 mounted on a W1 Fin on a c5180. The cust broke off the attachment sensor arm that tells when the finisher is attached to the copier. A wedge of paper works for now but I can't find a good part #.
    I looked in the AH1 (couldn't find it) and W1 parts manuals and ordered #4A3-4180 from the W1 book but that wasn't it.


  2. #2
    Senior Tech 250+ Posts ReproKev's Avatar
    Join Date
    Feb 2009
    Location
    Newark, DE
    Posts
    256
    Rep Power
    35
    I still can't locate the sensor arm in the AH1 parts book. Anyone have a good part # by chance? Thanks.

  3. #3
    East Coast Imaging 2,500+ Posts
    Part # for attachment sensor arm for puncher unit AH1

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,399
    Rep Power
    69
    Quote Originally Posted by ReproKev View Post
    I still can't locate the sensor arm in the AH1 parts book. Anyone have a good part # by chance? Thanks.
    I tried but couldn't find it my self, I wasn't to sure.
    If you could find out what PI sensor that is, it would probably help.
    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  4. #4
    Senior Tech 250+ Posts ReproKev's Avatar
    Join Date
    Feb 2009
    Location
    Newark, DE
    Posts
    256
    Rep Power
    35
    The only thing I could find was the joint sensor (PI22) on the finisher W1. I had already ordered the flag for it but it wasn't the same.
    In the Puncher AH1 parts book there is a "joint sensor cable" (under attachment parts) that looks like an entension cable - possibly to move the original joint sensor from the fin to the puncher?
    Anyone have an installation manual from a puncher unit AH1? The answer may be in there.

  5. #5
    Service Manager 10,000+ Posts
    Part # for attachment sensor arm for puncher unit AH1

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by ReproKev View Post
    The only thing I could find was the joint sensor (PI22) on the finisher W1. I had already ordered the flag for it but it wasn't the same.
    In the Puncher AH1 parts book there is a "joint sensor cable" (under attachment parts) that looks like an entension cable - possibly to move the original joint sensor from the fin to the puncher?
    Anyone have an installation manual from a puncher unit AH1? The answer may be in there.

    I believe that part is attached to [6] Latch Unit (Component on the finisher side)circled in RED BELOW/ double click on pic

    latch..JPG
    LU..JPG

    DOUBLE CLICK ON PIC ABOVE

    that unit comes in puncher kit/ still looking for part #
    here u go below>>>>>>>



    The part number to the upper latch cover is 4F3-0930-000. The part number to the lower latch cover is 4A3-4188-000 lower latch cover. The covers are shown in the Puncher Unit AH1 in the image below but there are no part numbers listed.





    the part numbers to the latch covers on the Punch Unit AH1

    Answer :
    The part number to the upper latch cover is 4F3-0930-000. The part number to the lower latch cover is 4A3-4188-000 lower latch cover. The covers are shown in the Puncher Unit AH1 in the image below but there are no part numbers listed.
    Last edited by teckat; 07-20-2010 at 12:04 AM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #6
    Senior Tech 250+ Posts ReproKev's Avatar
    Join Date
    Feb 2009
    Location
    Newark, DE
    Posts
    256
    Rep Power
    35
    Thanks for finding that! It's on order now, hopefully the flag will come attached to it. I'll post back to let you know.

  7. #7
    Service Manager 10,000+ Posts
    Part # for attachment sensor arm for puncher unit AH1

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by ReproKev View Post
    Thanks for finding that! It's on order now, hopefully the flag will come attached to it. I'll post back to let you know.

    If you are talking about that black push button on Puncher it should be on that Puncher Latch Unit Upper Cover/ that is what strikes the Flag Latch Sensor Flag on Finisher W1 Frame.

    if also needed
    u can try this - Finisher Flag Latch sensor> 4A3-4180-000

    That part is listed on Finisher W1 Part Book as behind Finisher Latch Cover/which u remove when u install a Puncher

    The Flag engages Puncher Latch Unit black button .
    Last edited by teckat; 07-20-2010 at 02:59 AM.

  8. #8
    East Coast Imaging 2,500+ Posts
    Part # for attachment sensor arm for puncher unit AH1

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,399
    Rep Power
    69
    Nice find teckat.
    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here