Tech Tips_imageRUNNER C5180 Series

[teckat]

TIPS:
imageRUNNER C5180 Series

1.Symptom: 2nd Side Image Registration is off: Lead and Trail
Registration moves when doing 2-sided printing/copying.
When printing or copying high density color products and
using 2-sided printing, the 2nd side lead and trail registration
varies causing the image to go off the page.
Solution: REG-SPD (SERVICE MODE (Level 2) > COPIER >
OPTION > BODY>REG-SPD: "Fine adjustment (Plain paper) of
the Registration Roller speed”) is a new service mode setting that
has been introduced to improve Second Side Mis-Registration
image shift.
Execute the fine adjustment of Registration Roller speed in
this mode to improve:
The second side of a printed or copied document has shifted
out of specification (2.5 +/- 2.0mm leading edge margin on the
2nd side). Setting values>5 to + 5 (Default factory setting/ value
after RAM clear: 0) Increasing (decreasing) the setting value by
"1" accelerate (decelerate) the delivery speed of the roller by
"0.5%". (Example: Changing the value from 0 to - 2 decelerates
the speed by 1.0 %.)

2.imageRUNNER C5180 Series
Symptom: Error Code E007-0001 or E007-0002 are displayed
and cannot be cleared.
Error Code E007-0001 refers to the inability of the upper
fixing belt to properly align itself according to the upper alignment
sensor. Error Code E007-0002 refers to the inability of the
lower pressure belt to properly align itself according to the lower
alignment sensor. Both of these codes can be attributed to badly
worn/stripped 14T Pinion Gears and/or their mating Fan Gears.
Solution: Replace both 14T Pinion Gears with their metal replacements,
part number FU7-0742-000 and also check their mating
Fan Gears for wear and replace them if necessary. Part numbers
for the Fan Gears are shown below. Once replaced,
install the fixing assembly and be sure to clear the error codes:
(COPIER>FUNCTION>CLEAR>ERR) and recycle power.
Once the fixing assembly is warmed up and the copier is at a ready
state, perform the following: COPIER>FUNCTION>
FIXING>FX-UHP-S and FX-LHP-S. Both must show OK!
GEAR..JPG
G1..JPG

[Canuck]

wonderful fusers...i have a 134 page bulletin from Canon just on that fuser...M9-045-3

[teckat]

no matter what u replace or adjust/ these fixing' units stink
CopyMachineAnnoy_.jpg

[lagustacat]

I have replaced a Canon IRC 5180 fuser assembly brand new 3 months ago and it crapped out, E007-0001 Error, anybody can tell me why this happens,

no matter what u replace or adjust/ these fixing' units stink
CopyMachineAnnoy_.jpg

[teckat]

I have replaced a Canon IRC 5180 fuser assembly brand new 3 months ago and it crapped out, E007-0001 Error, anybody can tell me why this happens,

where did u buy this Unit ????

did u do this adjustment in service mode after install-????
- Service Mode COPIER>FUNCTION>FIXING>FX-UHP-S (Fixing belt displacement control auto home position search)
- Service Mode COPIER>FUNCTION>FIXING>FX-LHP-S (Pressure belt displacement control auto home position search)

******DO NOT DO THIS ADJUSTMENT NOW ---READ THE PDF

u can sometimes reverse this code with these checks/adjustments-

read this pdf>>

[lagustacat]

I did not do this adjustment before installing fixing unit, it was purchased from DSN, any ideas why it stopped working, am i suppose to do this service adjustment after this installation of brand new fuser, i do have all of canons tech publications

where did u buy this Unit ????

did u do this adjustment in service mode after install-????
- Service Mode COPIER>FUNCTION>FIXING>FX-UHP-S (Fixing belt displacement control auto home position search)
- Service Mode COPIER>FUNCTION>FIXING>FX-LHP-S (Pressure belt displacement control auto home position search)

******DO NOT DO THIS ADJUSTMENT NOW ---READ THE PDF

u can sometimes reverse this code with these checks/adjustments-

read this pdf>>

[teckat]

I did not do this adjustment before installing fixing unit, it was purchased from DSN, any ideas why it stopped working, am i suppose to do this service adjustment after this installation of brand new fuser, i do have all of canons tech publications

u need to do that FIX UNIT procedure for all iRC5180 series MODELS/
when u install a new or refurbed fix unit

remove the fix unit and inspect belt position/
pdf shows an adjustment for Home Position/
try it/

[lagustacat]

I have removed the fuser and have adjusted belt as per tech bullitn 8a still same error

u need to do that FIX UNIT procedure for all iRC5180 series MODELS/
when u install a new or refurbed fix unit

remove the fix unit and inspect belt position/
pdf shows an adjustment for Home Position/
try it/

[teckat]

I have removed the fuser and have adjusted belt as per tech bullitn 8a still same error

check the top belt sensor wires unit--& sensors
they don't change those sensor units/ could be burnt out

the lower bearings are never replaced on refurb units
look for a black band on lower belt

may have a broken tooth on small brown gear/
to inspect u need to remove side drive units

Check the drive gears [1], [2], and [3] in the fixing assembly side for breakage; if any of them are broken, replace it with a new one.

E008-1.jpg
Check the gear [4] in the fixing driver assembly side for breakage.

E008-2.jpg

what is DSN warranty ?

[lagustacat]

Fuser is brand new, not a redurbished unit, no warranty from DSN, all items you would like me to check are brand new

check the top belt sensor wires unit--& sensors
they don't change those sensor units/ could be burnt out

the lower bearings are never replaced on refurb units
look for a black band on lower belt

may have a broken tooth on small brown gear/
to inspect u need to remove side drive units

Check the drive gears [1], [2], and [3] in the fixing assembly side for breakage; if any of them are broken, replace it with a new one.

E008-1.jpg
Check the gear [4] in the fixing driver assembly side for breakage.

E008-2.jpg

what is DSN warranty ?