Hi, I have 2 sets IRC3220n main unit , Both have no scanner and feeder, only working as network printer. how can we use auto full adjustment without scanner.
Hi, I have 2 sets IRC3220n main unit , Both have no scanner and feeder, only working as network printer. how can we use auto full adjustment without scanner.
You cann't. All you can do is a quick adjustment
Is there a Fiery Rip present? if this is the case, you can calibrate the Unit via "Command Workstation"
If sometimes you feel a little useless, offended and depressed always remember that you were once the fastest and most victorious sperm of hundreds of millions!
My apologize, i forgot to mention it.
Yes sure, you are in need of an es1000 or similar.
sorry
If sometimes you feel a little useless, offended and depressed always remember that you were once the fastest and most victorious sperm of hundreds of millions!
No Fiery Rip present. printer only
Is it workable for adjustment If I install a scanner taken from another IRC3220 copy machine. What we need to prepare and how to set up via the system command.
Do you mean swapped laser from another machine?
If you have replaced or swapped the laser unit, execute the following service mode:
COPIER>FUNCTION>LASER>L-ADJ-0
1) Remove all 4 color drum units, and close the front cover.
2) Select this item, and press the OK key to execute the operation. The operation stops automatically.
3) When automatic adjustment has finished, 'END' is displayed in the screen. Note The DC controller uses the photo diode in the laser unit to automatically measure the light quantity hence each laser emits its minimum light quantity. This operation is used to compensate the time the laser lights during minimum light quantity emission. Each laser unit Y/M/C/K) is adjusted in sequence.
Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC
Think they mean the READER -
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
Well in that case I would installed the image reader and the hardware, cable for communication.
Afterwards go into service mode and change.
Copier>Option>Body> W/SCNR. Change it to 1.
See what happens.
Not to sure that this can be done, only because Canon had two different item codes for each model. You can purchase a Image Reader C1 for the IRc3220/2620, item code 7761A002AA.
Give it shot I think it might work.
Let us know.
Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC
they also need to input the R-CON numbers in from behind side cover
COPIER>ADJUST>ADJ-XY>ADJ-X
COPIER>ADJUST>ADJ-XY>ADJ-Y
COPIER>ADJUST>ADJ-XY>ADJ-S
COPIER>ADJUST>CCD>W-PLT-X
COPIER>ADJUST>CCD>W-PLT-Y
COPIER>ADJUST>CCD>W-PLT-Z
COPIER>ADJUST>CCD>CLF-R-RG
COPIER>ADJUST>CCD>CLF-R-GB
COPIER>ADJUST>CCD>CL-R-RG
COPIER>ADJUST>CCD>CL-R-GB
COPIER>ADJUST>CCD>BW-R-RG
COPIER>ADJUST>CCD>BW-R-GB
COPIER>ADJUST>CCD>CCDU-RG
COPIER>ADJUST>CCD>CCDU-GB
COPIER>ADJUST>CCD>FCCDU-RG
COPIER>ADJUST>CCD>FCCDU-GB
RCON.JPG
RC5.JPG
Last edited by teckat; 08-24-2010 at 05:18 AM.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
Bookmarks