canon ir-2016 showing download standby

[tariq65]

i am facing this problem canon ir-2016 display showing download standby not work all keys.erroe red light glowing
ani body help me thanks.

[teckat]

i am facing this problem canon ir-2016 display showing download standby not work all keys.erroe red light glowing
ani body help me thanks.

did u just install a Printer Kit ??

The Display will show "Download Mode" or "Download Standby" even though the imageRUNNER was not put into download mode. This may also occur after installing the updated Printer Kit-J1 [0446B005AA]. Turning the power on and off will not reset the message.

flashing the machine to the latest system software may resolve the unusual message.

Note: Printer Kit-J1 [0446B005AA] requires the new system software v60.02 be installed on the imageRUNNER.


or re-flash the BOOT ROM with at least version 60.02.





Installing System Software on the imageRUNNER 2020 / 2016 Series

iR2016_2020.pdf






The following modules must be installed from a PC connected to the copier via a USB cable using the Service Support Tool:

- System (main controller) *
- Boot (boot program)
- PCL (PCL printer kit -J1)

* The main controller also controls the reader.

To flash the Finisher -U1 (Fin_U1), you must connect the PC to the finisher via a RS232C straight cable and the Downloader PCB (FY9-2034) using the Service Support Tool.

Due to copyright restrictions, the 2020/2016 System Software is not available for electronic download. Please order this 2020/2016 system software as a service part using Part Number FY9-4240-003.

To enter Download Mode on the imageRUNNER 2020 / 2016 Series:

1. Hit Additional Functions, 2, 8, and Additional Functions to enter Service Mode.
2. Press the + or - key to scroll through the Service Mode options.
3. Scroll to '#DOWNLOAD'.
4. Hit the OK key.

[android790]

I had this happen to me for no real reason. The flash fixed it. You should follow what teckat posted. Save yourself time and money.

[tariq65]

thak so mutch sir.

[mahmoud]

did u just install a Printer Kit ??

The Display will show "Download Mode" or "Download Standby" even though the imageRUNNER was not put into download mode. This may also occur after installing the updated Printer Kit-J1 [0446B005AA]. Turning the power on and off will not reset the message.

flashing the machine to the latest system software may resolve the unusual message.

Note: Printer Kit-J1 [0446B005AA] requires the new system software v60.02 be installed on the imageRUNNER.


or re-flash the BOOT ROM with at least version 60.02.





Installing System Software on the imageRUNNER 2020 / 2016 Series

iR2016_2020.pdf






The following modules must be installed from a PC connected to the copier via a USB cable using the Service Support Tool:

- System (main controller) *
- Boot (boot program)
- PCL (PCL printer kit -J1)

* The main controller also controls the reader.

To flash the Finisher -U1 (Fin_U1), you must connect the PC to the finisher via a RS232C straight cable and the Downloader PCB (FY9-2034) using the Service Support Tool.

Due to copyright restrictions, the 2020/2016 System Software is not available for electronic download. Please order this 2020/2016 system software as a service part using Part Number FY9-4240-003.

To enter Download Mode on the imageRUNNER 2020 / 2016 Series:

1. Hit Additional Functions, 2, 8, and Additional Functions to enter Service Mode.
2. Press the + or - key to scroll through the Service Mode options.
3. Scroll to '#DOWNLOAD'.
4. Hit the OK key.

Iis it necessary to flash the finsher, i mean will it work if didnt flash it. by only downloading:

-System (main controller)
- Boot (boot program)
- PCL (PCL printer kit -J1)

[teckat]

no/ not unless u have an issue with it/ or the firmware is old


READ THIS PDF>>important info on Firmware-iR2016 Firmware_TP11_141.pdf

[mahmoud]

no/ not unless u have an issue with it/ or the firmware is old


READ THIS PDF>>important info on Firmware-iR2016 Firmware_TP11_141.pdf

thnax alot. i have some questions about the following paragraph taken fro the pdf that u gave me.

:PROCEDURE:
Points to note when upgrading from ver. 10 or earlier to ver. 60 or later:
When upgrading from a previous version to v60.02, an “ALL Clear” will need to be performed. In order to
back up the required data files, System Software v15.99 for the imageRUNNER 2016/ 2020 or v10.99 for
the imageRUNNER 2016i/ 2020i will need to be installed first. When “ALL Clear” is performed after
System Software v15.99 for the imageRUNNER 2016/ 2020 and v10.99 for the imageRUNNER 2016i/
2020i has been installed, the following user information is deleted, so back up of all data is required
beforehand.
- Address Book
- User Data:

q1 is what is the "ALL CLEAR" , AND HOW TO DO IT Manually. q2 how can i know the firmware version of Machine if its always on download standby. thnx alot again u have been great help for me.

[teckat]

try to enter service mode> even though download message is present--

Use it to clear all settings/registration data except the counter (denominator, numerator)

To perform an 'ALL CLEAR', enter service mode by pressing additional functions > 2 then 8 and additional functions again. Scroll to #Clear and press ok. Next,select ALL and press ok. The imageRUNNER may power cycle itself.

Note*
After performing the ALL CLEAR, the imageRUNNER will be set to factory default and user inputted values will be lost.

Firmware ver= don't u have a Spec Report ??
To print a Spec Report from the imageRUNNER 2016 / 2016i / 2020 / 2020i:

1. Enter Service Mode by hitting Additional Functions > 2 > 8 > Additional Functions.

2. The Service Mode screen appears displaying [#SSSW].

3. Hit the Left Arrow 6 times. [REPORT] is displayed. Press OK.

4. Press the Right Arrow 1 time. [REPORT OUTPUT] is displayed. Press OK.

5. Hit the Right Arrow 5 times. [SPEC LIST] is displayed. Press OK.

6. The Spec Report is printed out.


u may be able to check in RUI

[eccsd]

try to enter service mode> even though download message is present--

Use it to clear all settings/registration data except the counter (denominator, numerator)

To perform an 'ALL CLEAR', enter service mode by pressing additional functions > 2 then 8 and additional functions again. Scroll to #Clear and press ok. Next,select ALL and press ok. The imageRUNNER may power cycle itself.

Note*
After performing the ALL CLEAR, the imageRUNNER will be set to factory default and user inputted values will be lost.

Firmware ver= don't u have a Spec Report ??
To print a Spec Report from the imageRUNNER 2016 / 2016i / 2020 / 2020i:

1. Enter Service Mode by hitting Additional Functions > 2 > 8 > Additional Functions.

2. The Service Mode screen appears displaying [#SSSW].

3. Hit the Left Arrow 6 times. [REPORT] is displayed. Press OK.

4. Press the Right Arrow 1 time. [REPORT OUTPUT] is displayed. Press OK.

5. Hit the Right Arrow 5 times. [SPEC LIST] is displayed. Press OK.

6. The Spec Report is printed out.


u may be able to check in RUI

Hi teckat,

I've just stumbled upon your posts here, but am wondering if it would be possible to flash my iR2016 using a Mac. (I haven't installed anything new at all, but don't have access to a Windows PC.)

Many thanks in advance for any and all advice!

[spectraindo]

Unfortunately the Canon SST work only on a Windows PC, there is no Mac version.