Canon IR5075 ADF Problem - Jam Code 0094

[teckat]

please help me to solve my problem.... i have canon ir 7105 machine.... its always jam when i start to use adf... jamming code 0094..... guys i really need your help.... thank you

---

imageRUNNER 7105

The quickest way to troubleshoot a 0094 is to use the FEEDER IO section found in service mode. COPIER>IO>FEEDER.

The sensors listed that can cause a 0094 jam are PI4 / PI12 / PI13 / S1 / S2 / S3 / S4 / S5 / S9.
Each of these sensors should be 0 no paper and 1 when paper is detected.

Use the IO mode to detect faulty sensor reading.

COPIER>IO>FEEDER.
P001 bit 1 = S2
P004 bit 7 = S9
P006 bit 4 = S4 P006 bit 7 = S3
P007 bit 1 = PI4 P007 bit 4 = S5 P007 bit 6 = S1
P008 bit 6 = PI13 P008 bit 7 = PI12

---

---

imageRUNNER 7105 / 7095 DADF-Q1

DADF-Q1 0094 Jam Code

Jam code 0094 is logged when the start button is pressed and using the DADF-Q1.
The original does not feed and power cycling the copier is the only way to reset the jam. --------------

Clean paper dust from the DADF sensors and perform the sensor adjustment on page 4-22 to 4-23 of the DADF-Q1 Service Manual.

The following image shows the procedure from the Service Manual highlighted in red.

[saidone]

IR 5075 machine, ADF problem, paper jam after replace inner roller and all rubber roller. It run several sheets of paper and jammed, so on and so on. How to solve it?
THX.

[teckat]

IR 5075 machine, ADF problem, paper jam after replace inner roller and all rubber roller. It run several sheets of paper and jammed, so on and so on. How to solve it?
THX.

Codes
Paper size
Copies or prints or on both

[dan7777]

Copier has a Jam code 0094,
When the copier is turned on without using adf everything is ok, but as soon as I put a sheet of paper to ADF and hit start, copier shows paper jam. When you turn of and on jam is gone.
I clean all sensors and reflective pads.

Please help.

Thank you all.

0094 in adf is a hard one. It means one of the sensors is blocked or failed when machine turned on. Some of them are hidden. I do not have but one or two of those models any more so I am used to the advanced models. Have had to swap out two doc feeders for this code. You basically have to check every sensor.

[Raoufselwaness]

hi;
i have ir7105 at customer site, soddenly stopped printing, but i can ping it from any pc on network
also i can scan to any pc on network.
tried to reinstall the driver but no good
i used UFR II and the pcl v.15 and v87 and the driver can not detect the printer
please help
thanks raouf

[teckat]

hi;
i have ir7105 at customer site, soddenly stopped printing, but i can ping it from any pc on network
also i can scan to any pc on network.
tried to reinstall the driver but no good
i used UFR II and the pcl v.15 and v87 and the driver can not detect the printer
please help
thanks raouf

Perform the following steps:

1. Press the [Counter Check] button on the copier control panel.

2. Press the [Device Configuration] button on the LCD screen.

3. Scroll down through all of the available pages on this Device Configuration screen. Look for either PS, PCL or UFRII. The methods listed here (ex. PS, PCL, or UFRII) are installed and are available for printing.

[nardinard]

igot jam 0094 to

copier>I0>Feeder
P0003 - 0(0/1)000000

i have P0003 bit 1 with 0 and 1 blink
what is mean.
pls help.

[teckat]

igot jam 0094 to

copier>I0>Feeder
P0003 - 0(0/1)000000

i have P0003 bit 1 with 0 and 1 blink
what is mean.
pls help.

Sensor bit check in I/O mode Blinking on n' off can mean a few things depending on type and location of sensor.

Could be loose flag action, short in connection, dirty led face, improper voltages.

What is model ?

[nardinard]

Sensor bit check in I/O mode Blinking on n' off can mean a few things depending on type and location of sensor.

Could be loose flag action, short in connection, dirty led face, improper voltages.

What is model ?

canon IR5075.
thx for replay

[teckat]

canon IR5075.
thx for replay

---

what Dadf do u have ???? copier>I0>Feeder bit 1 P0003 - 0(0/1)000000 5075 Printer Service Manual --FEEDER P003 Bit 1 = is the feed motor current setting CUT ???? S1 Manual I/O >FEEDER SL1 P003-1 1:ON SL-CHK>1 DADF-M1 DADF-S1

Title : 0094 Jam Code

The document feeder is generating a 0094 jam code that will not clear until the machine is power cycled. A 0094 jam code can be generated by any paper path sensor in the document feeder. Any of the path sensors (PI1, PI11, PI12, PCB2, PCB3, PCB4) can cause a 0094 jam code. Solution : Returning the prism for PI7(DADF M1) / PCB2(DADF S1) to its proper position, resolved this issue. See photo below for location of sensor prism.

================================================== ==================================================

EXAMPLE---------------------a foreign object was found interfering with the flag actuator operation of PI11.
The picture below shows the location of PI11.