Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 8 of 8
  1. #1
    y_us1982
    Guest

    iRC3220 scanning problem

    my iRC3220 machine on field had problem when using an adf. it only can read 2 pieces of paper only, when the 3rd paper is loaded into the adf, the paper will jam. i had try it so many times but it goes the same. but when i used a4r on the adf, the paper will just go fine. is it i have to initialize the sensor in svc mode?

    1 more thing, the margin is getting too far. i try to adjust the margin but still goes the same.

    anybody knows how to solve this? thanks in advance...

  2. #2
    Service Manager 10,000+ Posts
    iRC3220 scanning problem

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by y_us1982 View Post
    my iRC3220 machine on field had problem when using an adf. it only can read 2 pieces of paper only, when the 3rd paper is loaded into the adf, the paper will jam. i had try it so many times but it goes the same. but when i used a4r on the adf, the paper will just go fine. is it i have to initialize the sensor in svc mode?

    1 more thing, the margin is getting too far. i try to adjust the margin but still goes the same.

    anybody knows how to solve this? thanks in advance...

    SERVICE MODE

    FEEDER>ADJUST>DOCST

    • Increasing the value makes the leading edge blank smaller.
    Adjustment –100 to 100 (0.337 mm units)
    Operation
    1) Place the document on the ADF document tray.
    2) Select the item, use the numeric keypad to change the setting value, then
    press the OK key to set it.
    3) Press the OK key again to deliver the document and stop it (aligned left)
    on the platen glass.
    4) Open the ADF carefully, and check the stop position of the document.
    Standard: Stop position L4 = 0 ± 1 mm
    L4: =Distance from vertical size plate edge to document edge

    Dip-switch functions
    The dip-switch (DSW1) functions of the ADF controller PCB are as follows.
    Normal settings Normal operation status is when all bits are OFF.
    Document tray adjustment=
    1) Set bits 3 and 4 ON.
    2) Set the document tray to the following sizes and
    press the push switch.
    · A/B: A4
    · Inch: LTR
    3) Set the document tray to the following sizes and
    press the push switch.
    · A/B: A4R
    · Inch: LTRR
    4) Press the push switch (SW1) again and set all bits
    back to OFF

    Sensor level adjustment (sensitivity adjustment)
    This adjustment is to be carried out when replacing the ADF controller board, document set sensor (U503), final document detection sensor (U504), pre-registration sensor (U502), reverse outlet sensor (U505).
    1) Stick an all black piece of paper over the final document detection sensor on the document tray.
    Make sure the black paper is not over the document set sensor.
    2) Close the ADF and enter service mode FEEDER > FUNCTION > SENS-INT.
    3) Press ‘OK’.
    About 15 seconds later, the document detection LED will flash twice, the display will change from SERVICE to READY. This means that the automatic adjustment is completed.


    DF.JPG
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    y_us1982
    Guest
    thanks teck, the probs had been done.

    one more thing, does anybody had manual how to replace lower/upper for irc3220 machine?

  4. #4
    Service Manager 10,000+ Posts
    iRC3220 scanning problem

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by y_us1982 View Post
    thanks teck, the probs had been done.

    one more thing, does anybody had manual how to replace lower/upper for irc3220 machine?
    FX-1.JPGFX-3.JPGFX-2.JPG
    F1.JPGF2.JPGF3.JPG
    F4.JPGF5.JPGF6.JPG
    F7.JPG
    to be continued>>>>>>>>>>>>>
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Service Manager 10,000+ Posts
    iRC3220 scanning problem

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #6
    Service Manager 10,000+ Posts
    iRC3220 scanning problem

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #7
    y_us1982
    Guest
    thanks teck for the brief explanation.

  8. #8
    Service Manager 10,000+ Posts
    iRC3220 scanning problem

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    I just hoped u were talking about the fuser & not the DF
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here