Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 22
  1. #11
    felixdl
    Guest

    Ir 2200 rx manual

    How can I Setup the fax to change from : rx auto to rx manual ?

    Tank you

  2. #12
    Service Manager 250+ Posts
    Join Date
    Sep 2008
    Posts
    384
    Rep Power
    35
    Please read the Facsimile Guide.

  3. #13
    Service Manager 10,000+ Posts
    Help with IR2200 install

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by felixdl View Post
    How can I Setup the fax to change from : rx auto to rx manual ?

    Tank you

    By default, these expanded RX functions are not enabled. These functions are not high priority items, but are useful in certain environments. The most familiar or most used item would be the Incoming Ring function. Here, you can control the number of rings it takes before the fax will answer. The other items such as RX Mode, Remote RX & Manual / Auto Switch are mainly used in an environment in which the phone line is shared.

    There are two ways to expand the RX functions depending on the imageRUNNER model:

    * If the imageRUNNER has a FAX based Service Mode: Enter Service mode>Special>Special SW><SW27 bit 7 to 1>

    * On Standard imageRUNNER Service modes: Enter Service mode>FAX>NCU>SpecialB><SW27 bit 7 to 1>

    Once SW 27 bit 7 is set to 1, power cycle the imageRUNNER, select ADDITIONAL FUNCTIONS>COMMUNICATIONS SETTINGS><under FAX SETTINGS><select RX SETTINGS>All expanded RX functions will now be displayed.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #14
    felixdl
    Guest
    Tank for your time
    First, i guest that the service mode is the same as the diagnostic mode?
    Then what i found there was
    FAX>NCU>SpecialB>
    SW27 0 1 0 1 0 1 1 1

    so it was already in good state i guest?
    But i've changed the seventh one to see, and even if i restart the Imagerunner, the menu dosen't change, dosen't get full of option in rx settings, either the sw27 is 1 or 0.

    Where do i'm wrong?
    Tank you again

  5. #15
    Service Manager 10,000+ Posts
    Help with IR2200 install

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by felixdl View Post
    Tank for your time
    First, i guest that the service mode is the same as the diagnostic mode?
    Then what i found there was
    FAX>NCU>SpecialB>
    SW27 0 1 0 1 0 1 1 1

    so it was already in good state i guest?
    But i've changed the seventh one to see, and even if i restart the Imagerunner, the menu dosen't change, dosen't get full of option in rx settings, either the sw27 is 1 or 0.

    Where do i'm wrong?
    Tank you again

    after u set SW7 BIT TO 1
    RE START/ then go in to >>>
    ADDITIONAL FUNCTIONS>COMMUNICATIONS SETTINGS><under FAX SETTINGS><select RX SETTINGS>All expanded RX functions will now be displayed.
    and make adjustments
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #16
    felixdl
    Guest
    What i means is the sw27 bit 7 was already 1, since the beginnig
    and under communication setting i don't have fax setting.
    Tank you for your patience

  7. #17
    Service Manager 10,000+ Posts
    Help with IR2200 install

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Quote Originally Posted by felixdl View Post
    What i means is the sw27 bit 7 was already 1, since the beginnig
    and under communication setting i don't have fax setting.
    Tank you for your patience
    Have u look under the ADDITIONAL FUNCTIONS>System Settings screen for> COMMUNICATIONS SETTINGS ?????? click on picture below

    screen..JPG
    If u don't see COMMUNICATIONS SETTINGS=u have no Fax Board installed
    When the FAX Board is not attached, “Report Settings,” “Custom Fax Settings,” and
    “Communications Settings” are not displayed


    Do you have the (Optional) Super G3 Fax Board-J1 installed on this printer ?????

    go in service mode
    Starting Service Mode and Making Selections
    1) Press the User Mode key * .
    2) Press ‘2’ and ‘8’ on the keypad at the same time.
    3) Press the User Mode key * on the control panel.
    Press the Reset key once to return to the Service Mode Initial screen .
    • Press the Reset key twice to end service mode and return to the User screen.

    look for FAX tab indicator for it's mode
    Last edited by teckat; 06-04-2010 at 08:00 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #18
    felixdl
    Guest
    This machine use to be the main one in the office, and every fax passed through her. Now this is the secondary machine nd I don't want her to answer but I still want to send fax.
    I see ADDITIONAL FUNCTIONS>System Settings screen for> COMMUNICATIONS SETTINGS , after that, there is nothing about custom fax setting . AT this place I can change the speed (33600) and some other thing, but I see some free space in this 3 pages menu.
    Since the beginning this parameter is that way : FAX>NCU>SpecialB> SW27 0 1 0 1 0 1 1 1

    Thank you again

  9. #19
    Service Manager 10,000+ Posts
    Help with IR2200 install

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244
    Enter Service Mode : Fax > Type > Site Setting >change to a different country then u are in/ u will be able to send and it will block all incoming faxes
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  10. #20
    brianburks
    Guest

    Same issue with additional fax RX settings

    I own an ir3025. The machine shares the telephone line with voice users. I need the fax line to listen for an incoming fax and take over when the incoming call is from a fax machine. I have read the posts from Tekcat to a user regarding expanded communications settings. I do not have the ability to view the expanded communications settings. I have verified that bit 7 is set to 1 as noted in the posts and restarted my machine to no avail. Will you please advise?

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here