How can I Setup the fax to change from : rx auto to rx manual ?
Tank you
How can I Setup the fax to change from : rx auto to rx manual ?
Tank you
Please read the Facsimile Guide.
By default, these expanded RX functions are not enabled. These functions are not high priority items, but are useful in certain environments. The most familiar or most used item would be the Incoming Ring function. Here, you can control the number of rings it takes before the fax will answer. The other items such as RX Mode, Remote RX & Manual / Auto Switch are mainly used in an environment in which the phone line is shared.
There are two ways to expand the RX functions depending on the imageRUNNER model:
* If the imageRUNNER has a FAX based Service Mode: Enter Service mode>Special>Special SW><SW27 bit 7 to 1>
* On Standard imageRUNNER Service modes: Enter Service mode>FAX>NCU>SpecialB><SW27 bit 7 to 1>
Once SW 27 bit 7 is set to 1, power cycle the imageRUNNER, select ADDITIONAL FUNCTIONS>COMMUNICATIONS SETTINGS><under FAX SETTINGS><select RX SETTINGS>All expanded RX functions will now be displayed.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
Tank for your time
First, i guest that the service mode is the same as the diagnostic mode?
Then what i found there was
FAX>NCU>SpecialB>
SW27 0 1 0 1 0 1 1 1
so it was already in good state i guest?
But i've changed the seventh one to see, and even if i restart the Imagerunner, the menu dosen't change, dosen't get full of option in rx settings, either the sw27 is 1 or 0.
Where do i'm wrong?
Tank you again
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
What i means is the sw27 bit 7 was already 1, since the beginnig
and under communication setting i don't have fax setting.
Tank you for your patience
Have u look under the ADDITIONAL FUNCTIONS>System Settings screen for> COMMUNICATIONS SETTINGS ?????? click on picture below
screen..JPG
If u don't see COMMUNICATIONS SETTINGS=u have no Fax Board installed
When the FAX Board is not attached, “Report Settings,” “Custom Fax Settings,” and
“Communications Settings” are not displayed
Do you have the (Optional) Super G3 Fax Board-J1 installed on this printer ?????
go in service mode
Starting Service Mode and Making Selections
1) Press the User Mode key * .
2) Press ‘2’ and ‘8’ on the keypad at the same time.
3) Press the User Mode key * on the control panel.
Press the Reset key once to return to the Service Mode Initial screen .
• Press the Reset key twice to end service mode and return to the User screen.
look for FAX tab indicator for it's mode
Last edited by teckat; 06-04-2010 at 08:00 PM.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
This machine use to be the main one in the office, and every fax passed through her. Now this is the secondary machine nd I don't want her to answer but I still want to send fax.
I see ADDITIONAL FUNCTIONS>System Settings screen for> COMMUNICATIONS SETTINGS , after that, there is nothing about custom fax setting . AT this place I can change the speed (33600) and some other thing, but I see some free space in this 3 pages menu.
Since the beginning this parameter is that way : FAX>NCU>SpecialB> SW27 0 1 0 1 0 1 1 1
Thank you again
Enter Service Mode : Fax > Type > Site Setting >change to a different country then u are in/ u will be able to send and it will block all incoming faxes
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
I own an ir3025. The machine shares the telephone line with voice users. I need the fax line to listen for an incoming fax and take over when the incoming call is from a fax machine. I have read the posts from Tekcat to a user regarding expanded communications settings. I do not have the ability to view the expanded communications settings. I have verified that bit 7 is set to 1 as noted in the posts and restarted my machine to no avail. Will you please advise?
Bookmarks