Results 1 to 4 of 4
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Sep 2009
    Location
    Baltimore Area
    Posts
    74
    Post Thanks / Like
    Rep Power
    11

    IR 5055 with Error E000000-0010

    I have a Canon IR5055 with an error E000000-0010. What does that code reference to?


  2. #2
    Trusted Tech 50+ Posts
    Join Date
    Jun 2009
    Posts
    61
    Post Thanks / Like
    Rep Power
    11
    Code

    Description

    Remedy

    E000

    The heater fails to heat.
    After correcting the fault, be sure to reset the error. (COPIER>FUNCTION>CLEAR>ERR)

    0000

    After power-on, the reading of the main thermistor does not increase to 70 deg C or higher within 20 sec.

    - Replace the main/shutter thermistor.
    - Replace the DC controller PCB.

    0010

    The power has been turned off and then on without resetting the error.

    - Reset the error. (COPIER>FUNCTION>CLEAR>ERR)



    Hope it will help you.


  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jun 2009
    Posts
    61
    Post Thanks / Like
    Rep Power
    11
    1. In service mode > COPIER > DISPLAY > ANALOG, check
    the temperature displayed next to the following items:
          
    - FIX-U

          
    - FIX-UE

          
    - FIX-SHTR.

     
    With the fixing feeder assembly pulled out, make sure that the
    temperatures are as follows:

          
    - FIX-U: 20 deg. C

          
    - FIX-UE: 8 deg. C

          
    - FIX-SHTR: 8 deg. C
    If any of them is
    230 deg. C or higher, the main body may have
    a defective part (D-CON, cable, etc);
    To put it the other way
    around, it is unlikely that the upper fixing unit is faulty.
    Note: It’s relatively rare but a fault in the upper fixing unit causes
    the DC controller to go out of order.
    2. With the fixing feeder assembly set, check the temperature of
    the following item in service mode > COPIER > DISPLAY > ANALOG,

          
    [FIX-U, FIX-UE, and FIX-SHTR]

     
    If any of them is 230 deg. C or more (*), a short-circuit may occur with
    the corresponding thermistor / fixing feeder cable.

     
    * If the fixing assembly has cooled completely, the temperature will be
    same as the room temperature. If the measurement is performed
    right after the assembly is heated, the temperature will become 50
    to 200 deg C.

      
    3.
    If the temperatures do not change even though the fixing feeder assembly
    is pulled out and then inserted again, the following are conceivable:

        
    - The thermistor has an open-circuit.

        
    - The fixing feeder assembly cable is broken.

        
    - The DC controller is faulty.

        - A cable of the main body is broken.



  4. #4
    Field Supervisor 2,500+ Posts


    zoraldinho's Avatar
    Join Date
    Mar 2008
    Posts
    2,970
    Post Thanks / Like
    Rep Power
    52
    Quote Originally Posted by tmanamore View Post
    I have a Canon IR5055 with an error E000000-0010. What does that code reference to?
    Usually CLEAR-DCON help for this issue but first check thermistors counter (DRBL-1)

    A little knowledge is a dangerous thing

    Click here to be sure



Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here