Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 10 of 10

Thread: IR 5570 E 800's

  1. #1
    Senior Tech 100+ Posts
    Join Date
    Jul 2008
    Location
    Raleigh, NC
    Posts
    173
    Rep Power
    0

    Lightbulb IR 5570 E 800's

    I had a problem with the primary fan connector and was getting E 824's. I got aa schematic and tore the cabling apart to get to pin level repair to get that fix.

    Then got an E 804-0001. Pulled the DC Controller off to bench check the little yellow fuses on the DC Controller. All tested good. Put board back on copier and now I am getting E805-0002 dtl =0002.

    Driving me nutz. Suggestions? Does this happen mutch?


  2. #2
    Senior Tech 250+ Posts roho's Avatar
    Join Date
    Mar 2009
    Location
    Earth
    Posts
    492
    Rep Power
    22

    Re: IR 5570 E 800's

    once helped a fellow tech with a series of e 800 codes-turned out some wires were pinched at some point, and the machine began throwing codes around like it was a bingo hall. see if anything is pinched-it can be very easy to have that happen, or even a tie wrap may start to cut into a wire once it has been moved. Good luck!


  3. #3
    Service Manager 10,000+ Posts
    IR 5570 E 800's

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,153
    Rep Power
    213

    Re: IR 5570 E 800's

    FM3-(24/12 V)2-speed control (voltage)-
    Check J111=DC controller PCB


    E805 /There is a heat discharge fan error/there is a feed fan error.
    0001 =The heat discharge fan stop signal has been detected for 5 sec or more even when the
    heat discharge fan is on.
    0002 =The feed fan stop signal has been detected for 5 sec even when the feed fan is on.

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Field Supervisor 500+ Posts vigour's Avatar
    Join Date
    Aug 2010
    Posts
    980
    Rep Power
    25

    Re: IR 5570 E 800's

    I think you put the three wires back in the wrong order at some point, and you blew the controller.
    Double check by following the wiring on another machine to the connector above the door switch to see how it is laid out.

    I got those codes once when my fan cable broke, and I had no manual.
    Ended up replacing a controller.


  5. #5
    Service Manager 250+ Posts gensys's Avatar
    Join Date
    Jan 2011
    Location
    Yerevan, AM
    Posts
    326
    Rep Power
    17

    Re: IR 5570 E 800's

    Quote Originally Posted by Hopper View Post
    I had a problem with the primary fan connector and was getting E 824's. I got aa schematic and tore the cabling apart to get to pin level repair to get that fix.

    Then got an E 804-0001. Pulled the DC Controller off to bench check the little yellow fuses on the DC Controller. All tested good. Put board back on copier and now I am getting E805-0002 dtl =0002.

    Driving me nutz. Suggestions? Does this happen mutch?
    Check jamper 111, check (24 & 12)V > it is standart error for iR

    The Road will be Mastered by >>> the Going...

  6. #6
    Service Manager 10,000+ Posts
    IR 5570 E 800's

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,153
    Rep Power
    213

    Re: IR 5570 E 800's

    posted already :)

    extra stuff
    FM3/J111
    FM3=FK2-0840
    COPIER>I/O
    P013-0: half-speed/1:ON
    P013-1: full-speed/1:ON



    FM6 /J102
    FM6= FK2-0799/0800 (DC power supply unit)
    FM 6 is not available as a separate part. The Power Supply must be ordered.
    COPIER>I/O
    P012-3/ 1:ON


    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #7
    Senior Tech 100+ Posts
    Join Date
    Jul 2008
    Location
    Raleigh, NC
    Posts
    173
    Rep Power
    0

    Re: IR 5570 E 800's

    After many moons the copier is fixed. The DC Controller fixed the 824 primary fan problem.

    The 805-2 was a constant after I fixed the wiring and switched out the board. The connector for the fan on the back of the machine was not plugged squarely and had a kink in the wire bundle. They make those yellow wires so small and delicate.

    Thanks for everyone's help. I am glad to have this monkey off my back.

    Hopper


  8. #8
    Service Manager 10,000+ Posts
    IR 5570 E 800's

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,153
    Rep Power
    213

    Re: IR 5570 E 800's

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  9. #9
    Lead Service Technician 1,000+ Posts mrfixit51's Avatar
    Join Date
    Oct 2008
    Location
    Davenport, Iowa
    Posts
    1,979
    Rep Power
    40

    Re: IR 5570 E 800's

    Quote Originally Posted by Hopper View Post
    Thanks for everyone's help. I am glad to have this monkey off my back.

    Hopper
    Enjoy a monkey-free Friday!!!

    "Once a King, always a King, but once a Knight is enough!"

  10. #10
    Senior Tech 100+ Posts
    Join Date
    Jul 2008
    Location
    Raleigh, NC
    Posts
    173
    Rep Power
    0

    Re: IR 5570 E 800's

    Quote Originally Posted by mrfixit51 View Post
    Enjoy a monkey-free Friday!!!
    I'll drink to that! I hate mowing the lawn on a Saturday and thing about that stuff.

    Hopper


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here