Results 1 to 10 of 10
  1. #1
    Trusted Tech 50+ Posts mujibur's Avatar
    Join Date
    Jan 2009
    Location
    chennai
    Posts
    53
    Post Thanks / Like
    Rep Power
    12

    canon clc1180 error E072-0003

    This error is consistently coming, after 5-10 copies/print, error comes.
    Drawer connectors are already brand new, both sides.
    Transfer Cleaning Unit is working alright. (But not yet tried to swap with another unit)
    Transfer Cleaning Unit Cam is working also. (But not yet tried to swap with another unit)

    Anyone got any bright ideas as to how to diagnose this.

    Thank You


  2. #2
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,407
    Post Thanks / Like
    Rep Power
    159

    Re: canon clc1180 error E072-0003

    Check both sides of all the door switches for voltage. A switch that is failing will drop the supplied voltage 3 to 5 vdc. Replace the switch.
    Check both SW4 (Left front cover switch) and SW5 (Delivery Cover switch).

    E072-0002


    if u look above the Transfer drum cleaner
    locking motor- u will see a three pin connector with orange wires/next to it is a two pin red/black 24v connector
    i short out motor M8 engage signal/
    i use a paper clip/
    make a U shape of it /cut each end at a pointed angle/
    u have to measure angle length of clip because of distance depth of both connectors/
    with power off-remove both connectors -push in one end of clip on outside of 24v red wire-push other end of clip into pin 3 of outside orange wire connector-
    now push back in both connectors with the short clip attached

    pin.JPG

    Last edited by teckat; 07-17-2011 at 03:29 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Trusted Tech 50+ Posts
    Join Date
    Jan 2011
    Posts
    87
    Post Thanks / Like
    Rep Power
    8

    Re: canon clc1180 error E072-0003

    Sorry teckat, but the subcode is not 0003, its 0002. Typo error...
    Does the same steps to test applies for 0002?

    i am working with mujibur...


  4. #4
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,407
    Post Thanks / Like
    Rep Power
    159

    Re: canon clc1180 error E072-0003

    Transfer drum cleaner brush motor (M8)

    Yes, I figured it may be for 0002,
    Sorry,this procedure is for the M8 Brush motor
    , was going to fix that reply today

    it's been a long time since I have seen one of these dogs

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Trusted Tech 50+ Posts
    Join Date
    Jan 2011
    Posts
    87
    Post Thanks / Like
    Rep Power
    8

    Re: canon clc1180 error E072-0003

    thanks teckat, hoping for you assistance on the said matters soon...

    will wait.


  6. #6
    Field Supervisor 2,500+ Posts


    zoraldinho's Avatar
    Join Date
    Mar 2008
    Posts
    2,951
    Post Thanks / Like
    Rep Power
    52

    Re: canon clc1180 error E072-0003

    A little knowledge is a dangerous thing

    Click here to be sure



  7. #7
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,407
    Post Thanks / Like
    Rep Power
    159

    Re: canon clc1180 error E072-0003

    Year 1999/ 9/7/99
    September

    Canon Publishes 60 Tech pubs on the CLC 1100 SERIES
    hm00494_.gif




    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #8
    Trusted Tech 50+ Posts
    Join Date
    Jan 2011
    Posts
    87
    Post Thanks / Like
    Rep Power
    8

    Re: canon clc1180 error E072-0003

    Quote Originally Posted by zoraldinho View Post
    will check on this on site... thank u


  9. #9
    Trusted Tech 50+ Posts
    Join Date
    Jan 2011
    Posts
    87
    Post Thanks / Like
    Rep Power
    8

    Re: canon clc1180 error E072-0003

    by far the machine is working. customer hasn't logged in the E0072 complain yet since my last service. And i HOPE they wont.

    Just replaced another unit of Transfer cleaning Motor, The whole assembly.

    Thanks so much Guyz...

    But i was just wondering, in one of our CLC 11X0, in the Transfer Cleaning Motor, there are 3 orange wire, the 3rd wire(on the right most) is shorted directly to the color brown(5volts i suppose) -- what effect does it do or what is the purpose for that?


  10. #10
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,407
    Post Thanks / Like
    Rep Power
    159

    Re: canon clc1180 error E072-0003

    Quote Originally Posted by vishop View Post
    by far the machine is working. customer hasn't logged in the E0072 complain yet since my last service. And i HOPE they wont.

    Just replaced another unit of Transfer cleaning Motor, The whole assembly.

    Thanks so much Guyz...

    But i was just wondering, in one of our CLC 11X0, in the Transfer Cleaning Motor, there are 3 orange wire, the 3rd wire(on the right most) is shorted directly to the color brown(5volts i suppose) -- what effect does it do or what is the purpose for that?


    pin 3 on orange should be shorted to the red 24v wire on the two pin connector
    both connectors are side by side/ it prevents transfer cleaning engagement when TD is engaged with Drum

    old Macgyver.jpgfix

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here