canon Ir c3200

[jake24482]

I am working on ir c3200. customer using heavy paper when we change heavy paper it make light copy . it makes perfect copy on plan paper setting .if we keep plan paper setting and use heavy paper after five or six pages it does not fuse properly .Is there any setting i can change to make it work

[mrfixit51]

Going out on a limb here, but this may have some results for you...

COPIER>ADJUST level 2 <HV-TR>

The adjusted offset doesn’t become valid unless all of the following 6 items
are entered: 2TR-TGT, 2TR-SHR, TR-PPR, TR-ENV, TR-CLR and TRDUP.
The settings entered for all 6 items make up a single pattern. 8 patterns
can be stored in memory.

• 2TR-TGT1/2/3/4/5/6/7/8 (Used to adjust the offset to the secondary transfer target current.)
Adjustment range: –5 to +5 (2 μA units) (Value at time of factory shipment/value after
RAM clear: 0)
Increasing the setting value: Effective for images with toner spatter/water droplets.
Decreasing the setting value: Effective for images with white marks, white blotches,
rough-textured half-tones.
• 2TR-SHR1/2/3/4/5/6/7/8 (Used to adjust the offset to the secondary transfer paper-portion
voltage.)
Adjustment range: –5 to +5 (100 V units) (Value at time of factory shipment/value after
RAM clear: 0)
Increasing the setting value: Effective for images with toner spatter/water droplets.
Decreasing the setting value: Effective for images with white marks, white blotches,
rough-textured half-tones.
• TR-PPR1/2/3/4/5/6/7/8 (paper type item for secondary transfer offset adjustment)
1: Normal paper (Value at time of factory shipment/value after RAM clear: 1)
2: Recycled paper
3: Bond paper
4: Mother print
5: Card
6: Extra thick card
7: Special paper 1 (including labels)
8: Glossy paper
9: Special paper 2 (including Japanese paper)
10: Postcards/envelopes
• TR-ENV1/2/3/4/5/6/7/8 (environmental item for secondary transfer offset adjustment)
Enter value of COPIER>DISPLAY>MISC>ENV-TR.
1: Low-humidity environment (Value at time of factory shipment/value after RAM clear:
1)
2: Normal-humidity environment
3: High-humidity environment
• TR-CLR1/2/3/4/5/6/7/8 (color mode item for secondary transfer offset adjustment)
1: Full-color mode (Value at time of factory shipment/value after RAM clear: 1)
2: Monochrome mode
• TR-DUP1/2/3/4/5/6/7/8 (one/two-sided item for secondary transfer offset adjustment)
1: One-sided (Value at time of factory shipment/value after RAM clear: 1)
2: Automatic two-sided
3: Manual feed two-sided
11: Transparencies (color)
12: Transparencies (monochrome)

[teckat]

I am working on ir c3200. customer using heavy paper when we change heavy paper it make light copy . it makes perfect copy on plan paper setting .if we keep plan paper setting and use heavy paper after five or six pages it does not fuse properly .Is there any setting i can change to make it work

First do a dc con clear in service mode and input all label values, then you must perform a laser adjustment under service mode, <Function>Laser>L-ADJ-O>.
You must remove all drum kits prior to making this adjustment.
Then perform a CCD and full auto gradation.
Do the Auto Gradation for Heavy Paperand Plain Paper
If problem persists replace dc controller and re-install system software.

+++++you may also need to replace ITB Drive Motor M1

[yourownfree]

if you are printing from your computer use the manual tray as it should be, then select think paper on your computer on the driver. Then when you place the paper in the tray, tell it thick paper. If you are just copying, place the thick paper in the manual tray, its asks you the size and then it asks you the type, choose thick.

[teckat]

if you are printing from your computer use the manual tray as it should be, then select think paper on your computer on the driver. Then when you place the paper in the tray, tell it thick paper. If you are just copying, place the thick paper in the manual tray, its asks you the size and then it asks you the type, choose thick.

that has nothing to do with the issue

Cassettes Paper Weights=
17 lb. Bond to 110 lb. Index (64gsm – 209gsm) and Transparency

Stack Bypass = 64-253 gsm

Duplex = 64-209 gsm

i have customers who set up trays for Heavy with no issues at all