Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6
  1. #1
    Service Manager 1,000+ Posts
    Canon IR 5000 feed multi-feeds from decks.

    Desert Rat's Avatar
    Join Date
    May 2008
    Location
    Valley of the Sun
    Posts
    1,089
    Rep Power
    44

    Canon IR 5000 feed multi-feeds from decks.


    This may be one of those TIP's.
    Both decks are not feeding very well. I went over last week, pulled the feed head for the right
    deck and put two sheets of paper between the feed and sep rollers and pushed the gear. Both
    sheets fed together. I saw the torque limiter turn in the feed direction. So I swapped that
    limiter with the one in tray 4, the least used tray. (The spring for the sep roller is set at the
    lowest setting per the manual to reduce multi-feeds.) Same test the sheets separated.
    Test tray four, the sheets separated.
    It would multi-feed 3-4 sheets in a 15 page run. When I finished I ran 40-50 pages and so did
    the customer. Alls well right?
    They call back with the same problem today. I did clear all the jam codes so I will have some
    current codes which I will gladly share tomorrow.
    As I recall all the feed rollers had less than 10K on the counters.

    On the back wall of the machine behind the left feed deck, there is a white lever. What purpose does
    it serve? It moves easily back and forth. Is it attached to a solenoid or something?

    Any suggestions welcome

    Thanks

    Dr

  2. #2
    Service Manager 1,000+ Posts vigour's Avatar
    Join Date
    Aug 2010
    Posts
    1,034
    Rep Power
    42

    Re: Canon IR 5000 feed multi-feeds from decks.

    put the spring back in the middle, change the rollers.
    the last time i saw anyone adjust that spring was about 20 years ago. it should not be necessary.
    replace it if it is deformed.
    use fb2-7777 sep roller.
    adjust the pressure to the middle, if someone has played with it.
    you can swop the the separation unit between deck 1, and cassette 3 or 4

  3. #3
    Service Manager 10,000+ Posts
    Canon IR 5000 feed multi-feeds from decks.

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR 5000 feed multi-feeds from decks.

    Motor Driver PCB Assembly ??
    FG6-4947-000
    The pickup assembly possesses as many as 12 2-phase stepping motors of magnetic excitation type. Each motor is supplied with 24-V power from the motor driver PCB, and is
    turned on/off and its direction of rotation is controlled by pulse signals from the DC controller PCB.
    DECK2.JPGDECK3.JPGDECK4.JPGDECK.JPG
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Service Manager 1,000+ Posts
    Canon IR 5000 feed multi-feeds from decks.

    Desert Rat's Avatar
    Join Date
    May 2008
    Location
    Valley of the Sun
    Posts
    1,089
    Rep Power
    44

    Re: Canon IR 5000 feed multi-feeds from decks.

    Thanks for getting back so quickly. I am in front of the machine now.
    I just ran 5 sets of 17pgs from the right deck. No problems. All I did
    was fluff up the paper.
    The customer sez they do not usually fluff the paper. I think that is part
    of the problem this time of year in Phoenix. It has been hot and the due
    point has been up and down. Changes in humidity have been know to cause
    problelms like this inconsistant feed.
    Vigour, I will set the sring back to the middle setting. I am the only one that
    services this unit, so it must be my fault.
    Teckat, I have not had a problem with the motors coming on, it is what
    happens after that that is the problem.

    From the left deck I ran the same 17 pgs 5 sets. It jammed on the second set.
    A piece of paper was very skewed in the path, with one corner bent down.
    The lead corner toward the front of the machine.
    Does this sound familar? And it is intermittant.
    One thing I noticed about the left deck is that the small pick up rollers don't
    seem to come down evenly. Seems like the one in the back is a little late.
    It is difficult for me to actuate the left deck feed assembly when I have it out
    of the machine to check this.

    Any suggestions?

    Thanks

    DR

  5. #5
    Service Manager 10,000+ Posts
    Canon IR 5000 feed multi-feeds from decks.

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: Canon IR 5000 feed multi-feeds from decks.

    jam code is ??
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #6
    Service Manager 1,000+ Posts
    Canon IR 5000 feed multi-feeds from decks.

    Desert Rat's Avatar
    Join Date
    May 2008
    Location
    Valley of the Sun
    Posts
    1,089
    Rep Power
    44

    Re: Canon IR 5000 feed multi-feeds from decks.

    Opps sorry forgot to include these codes.

    The most frequent code from the right deck is 0 0110 1
    From the left deck I get 0 020F 2. I also get 0110 from the
    left deck.
    Right deck jam. When I clear the jam, I find 2 sheets, that separated under the
    drum, one was just into the nip of the fuser and the other was half way through
    the registration unit. Both had heavy dark lines of un-fuser toner from where the
    drum continued to turn for a second. Neither sheet was wrinkled.
    Sometimes both sheets would go through with out jamming.

    Left deck jam. It was about the same only the lead page was skewed in the path.
    If it got through the fuser it would get stuck in the delivery turn over area, because
    it was also skewed. And it was wrinkled with sharp creases.
    And as mentioned the front lead edge corner was bent over.
    Sometimes I would get a 010B (Retry sensor PS19 left deck).

    0110=delay internal delivery PS35
    020F=stationary claw sensor PS4

    Hope that helps.
    Thanks

    DR

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here