Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Senior Tech 100+ Posts alexctx's Avatar
    Join Date
    Dec 2010
    Location
    lima,Peru
    Posts
    158
    Rep Power
    0

    Question imagepress c7000vp

    not detect any pickup / delivery accessories.
    ARCNET , poder .cable. ok.
    have made​​. MN-CON CLEAR

  2. #2
    Service Manager 10,000+ Posts
    imagepress c7000vp

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagepress c7000vp

    Quote Originally Posted by alexctx View Post
    not detect any pickup / delivery accessories.
    ARCNET , poder .cable. ok.
    have made​​. MN-CON CLEAR

    ERROR CODE/JAM CODE
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Senior Tech 100+ Posts alexctx's Avatar
    Join Date
    Dec 2010
    Location
    lima,Peru
    Posts
    158
    Rep Power
    0

    Re: imagepress c7000vp

    not detect.
    POD Deck-A1, Saddle Finisher-AB2, Booklet Trimmer-C1.
    only have these accessories.
    this figure only.

    Dibujo.JPG

  4. #4
    Service Manager 10,000+ Posts
    imagepress c7000vp

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagepress c7000vp

    Quote Originally Posted by alexctx View Post
    not detect.
    POD Deck-A1, Saddle Finisher-AB2, Booklet Trimmer-C1.
    only have these accessories.
    this figure only.

    Dibujo.JPG

    imagePRESS C6000 / C6000VP / C7000VP

    Copier does not Recognize any of the Options

    After you OHM out the Arcnet cable for continuity (1-1.5ohms) and checked or replaced the terminator end caps, check the DC Controller, 1-1 connector J1055 to the Arcnet Connection p.c.b. J4500 to see if they are secure.

    Archnet.jpg
    Check the ARCNET cable behind the DC Controller cage for proper connection.
    The ARCNET cable meets at a T junction and connects to the transceiver pcb assembly then connects to the DC Controller-
    Two ways to check to see if ARCNET cable is connected:
    1. remove entire DC Controller cage
    2. remove screws holding cage to main frame and insert hand underneath through the bottom section and feel for the ARCNET junction connection.

    If the machine was previously working with all accessories attached and suddenly they drop off line, even though the power to the accessory (accessories) is on, make the following checks:

    * Make sure in service mode Copier/Option/ACCPT-D, or ACCPST-P that the options are added in the correct order and that the status is set to 1.
    * Check the Arcnet connection to all accessories and make sure it is terminated at both ends.

    NOTE:
    Here's an easy and quick way to check the arcnet bus: Disconnect the arcnet cables from each end of the bus and make a continuity check from end to end. The reading should be about 1 to 1.5 ohms.

    Arcnet1.jpg
    * If the arcnet bus is open (measures infinity) start troubleshooting by checking each cable section for continuity until the problem is found. Here's an example of an arcnet cable where the outer ring was pulled causing the inner contact to slip into the cabling resulting in no contact with the coupling between the marking engine and the substation:
    Arcnet2.jpg
    * If the arcnet checks good try replacing the terminators with brand new ones. Be sure to order the correct terminators, the impedance is different on some arcnet buses such as the iR110 series.
    NOTE: The impedance of the terminators on the arcnet bus on the imagePRESS VP series is 75ohms. However, we have confirmed that you can have a bad terminator and still measure 75ohms, the recommendation is to replace the terminators at both ends regardless.

    * If the previous checks are all good and you have replaced the terminators next try replacing the transceiver pcb's, there will be one on each accessory and one located behind the DC Controller pcb 1 on the Marking Engine.

    PART NUMBER REFERENCE:

    * Terminator: WS6-5201-000
    * Interface PCB Assy for High Capapcity Stacker C-1 : FM2-6168-000 (same part number for marking engine and all accessories)
    * Cable, Interface: FM2-5756-000
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Senior Tech 100+ Posts alexctx's Avatar
    Join Date
    Dec 2010
    Location
    lima,Peru
    Posts
    158
    Rep Power
    0

    Re: imagepress c7000vp

    the Arcnet cable ok.
    check the DC Controller j1055,j4500 . tomorrow morning I'll do that.
    there will be something. to set copier options ?
    ACCPT-D, o ACCPST P 0

  6. #6
    Senior Tech 100+ Posts alexctx's Avatar
    Join Date
    Dec 2010
    Location
    lima,Peru
    Posts
    158
    Rep Power
    0

    Red face Re: imagepress c7000vp

    affine. the problem was a simple terminal.
    If you do not put the ipc7000vp, C6000, sometimes detected, sometimes not.
    the accessories.
    have to go on both ends of the accessories connected.
    this measure 75ohms .



    3JCAOPO94NCAS5PY3GCA43BE61CAC0VQ57CACFI7YQCADFXOTICAE6Y6POCAXXDEW6CA0JIFSLCA2JNR2JCA2240I0CABUW4.jpg

  7. #7
    Service Manager 10,000+ Posts
    imagepress c7000vp

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: imagepress c7000vp

    Quote Originally Posted by alexctx View Post
    affine. the problem was a simple terminal.
    If you do not put the ipc7000vp, C6000, sometimes detected, sometimes not.
    the accessories.
    have to go on both ends of the accessories connected.


    3JCAOPO94NCAS5PY3GCA43BE61CAC0VQ57CACFI7YQCADFXOTICAE6Y6POCAXXDEW6CA0JIFSLCA2JNR2JCA2240I0CABUW4.jpg


    Whew_Full.jpg

    Old Saying'
    Measure Twice > Cut Once
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here