Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 12
  1. #1
    Senior Tech 100+ Posts DANIELCANON's Avatar
    Join Date
    Jun 2011
    Location
    lima,peru
    Posts
    188
    Rep Power
    0

    help IR5075 code E202 - 0101

    hi, este codigo aparece esporadicamente. apago y enciendo el equipo y se corrige pero despues de un tiempo vuelve.gracias.


  2. #2
    teacher-guide-expert-guru 2,500+ Posts
    help IR5075 code E202 - 0101

    zoraldinho's Avatar
    Join Date
    Mar 2008
    Location
    SVN
    Posts
    4,081
    Rep Power
    75

    Re: help IR5075 code E202 - 0101

    The scanner does not return to the home position for vertical
    scanning within a specific time.

    Ir6570 e202-0002

    Practice makes perfect
    If it ain't broke, don't fix it
    There's no such thing as a free lunch
    A picture is worth a thousand words
    If you want something done right, you have to do it yourself


  3. #3
    Service Manager 10,000+ Posts
    help IR5075 code E202 - 0101

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,155
    Rep Power
    213

    Re: help IR5075 code E202 - 0101

    what tests have u tried so far ??????

    check your ribbon connector on the reader controller

    remove & re-seat the ROM on the Memory pcb board /Reader

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Senior Tech 100+ Posts DANIELCANON's Avatar
    Join Date
    Jun 2011
    Location
    lima,peru
    Posts
    188
    Rep Power
    0

    Re: help IR5075 code E202 - 0101

    gracias a ambos, les estare informando lo sucedido estos dias


  5. #5
    Field Supervisor 500+ Posts Rachid.Akli's Avatar
    Join Date
    Oct 2011
    Location
    Algiers
    Posts
    585
    Rep Power
    20

    Re: help IR5075 code E202 - 0101

    You've to notice something important in this model: The DADF is equiped with a reading CIS. A duplex document is read with a single passage. So, open the DADF from the upper side. get access to the CIS rails, clean and lubricate.

    Rachid.


  6. #6
    Senior Tech 100+ Posts DANIELCANON's Avatar
    Join Date
    Jun 2011
    Location
    lima,peru
    Posts
    188
    Rep Power
    0

    Re: help IR5075 code E202 - 0101

    muchas gracias efectivamente el codigo aparece solo cuando se utiliza el alimentador de documentos ya que cuando se copia desde el vidrio no indica codigo.
    hay alli dentro unas correas que me han dicho que hay que ajustarlas. puede alguien enviarme informacion sobre el alimentador de documentos. gracias


  7. #7
    Service Manager 10,000+ Posts
    help IR5075 code E202 - 0101

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,155
    Rep Power
    213

    Re: help IR5075 code E202 - 0101

    Quote Originally Posted by DANIELCANON View Post
    muchas gracias efectivamente el codigo aparece solo cuando se utiliza el alimentador de documentos ya que cuando se copia desde el vidrio no indica codigo.
    hay alli dentro unas correas que me han dicho que hay que ajustarlas. puede alguien enviarme informacion sobre el alimentador de documentos. gracias





    thank you very much indeed the code appears only when using the document feeder as when copying from the glass does not indicate code.
    straps is in there they told me to be adjusted. can someone send me information on the document feeder. thanks




    Remove covers following directions in Chapter 3 in the IR5075 DADF service manual to access CIS drive motor and belt. Item 13 Figure A40, in the IR5075 parts manual is the belt clamp. Loosen the two screws and apply pressure to the clamp making sure the belt teeth are seated in the clamp. Tighten the screws and test for CIS homing and white plate reading. With the DADF front cover removed you can watch the CIS move from home to reading position by powering the IR5075 off and on


    E202-0101: Backside reading glass (Contact Image Sensor - CIS) Home Position Error. The home position
    cannot be detected in the direction (outward) of the home position of the CIS.
    1. Open the top cover of the DADF.
    DF.JPG
    2.Remove the input baffle.
    3. Remove the turn-around baffle.
    DF2.JPG
    The E202-0101 is caused from the belt shown below not being adjusted properly or the M6 motor not getting proper voltage. Also check that the Glass Holder Assembly moves freely with no binding. Check the tie wraps on the connector for the M6 motor.
    --------------------------------------------
    Adjust belt tension/ U NEED TO LOOSEN THE SCREW ON PLATE > SCREW IS NEAR THAT SMALL PCB /U NEED A SMALL SCREWDRIVER TO FIT IN GAP>THEN PUSH GEAR TO TIGHTEN BELT> THEN TIGHTEN SCREW IN PLACE. DO NOT MAKE BELT TO TIGHT> IT WILL SKIP AND CAUSE NOISE & SAME ERROR CODE
    DF3.JPG

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  8. #8
    Senior Tech 100+ Posts DANIELCANON's Avatar
    Join Date
    Jun 2011
    Location
    lima,peru
    Posts
    188
    Rep Power
    0

    Cool Re: help IR5075 code E202 - 0101

    efectivamente es esa la correa la cual en un primer momento parece que la ajuste demasiado porque la maquina indico el dicho codigo apenas la encendi, pero luego regule esa correa y ya no a marcado dicho codigo pero la copiadora esta a prueba por el cliente para ver si en los proximos dias indica dicho codigo estare informando gracias a todos.

    DF3.JPG


  9. #9
    Senior Tech 100+ Posts DANIELCANON's Avatar
    Join Date
    Jun 2011
    Location
    lima,peru
    Posts
    188
    Rep Power
    0

    Smile Re: help IR5075 code E202 - 0101

    teckak tengo una duda yo he aplicado presion a la correa destornillando el motor con tres tornillos pequeños que tiene este; pero tu mencionas dos tornillos para ajustar la pinza. ¿cual es dicha pinza podrias ser mas detallista o mostrar mas fotos gracias.


  10. #10
    Service Manager 10,000+ Posts
    help IR5075 code E202 - 0101

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    15,155
    Rep Power
    213

    Re: help IR5075 code E202 - 0101

    Quote Originally Posted by DANIELCANON View Post
    teckak tengo una duda yo he aplicado presion a la correa destornillando el motor con tres tornillos pequeños que tiene este; pero tu mencionas dos tornillos para ajustar la pinza. ¿cual es dicha pinza podrias ser mas detallista o mostrar mas fotos gracias.
    sorry, i meant to say you move the motor

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here