Results 1 to 10 of 10
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jan 2008
    Posts
    67
    Post Thanks / Like
    Rep Power
    14

    iRAC9065PRO, E002-0102

    Dear All,
    I have a problem of iRAC9065PRO
    Now, it displays error code E002-0102 upon turn it on
    I checked in service mode: Display>Analog>Fix-LC, Fix-LE, Fix-LE2. The values are always under 70oC
    I assume that halogen lamp not turn on. The pressure roler has been heated up by fixing roler.
    I take that halogen lamp out and check by meter, it is still ok, no crack, no disconnection
    I refer in service manual it suggest to check AC driver PCB, DC controller...
    The IH heater is working well, temp approach over 170oC so I do not think about AC driver PCB
    Have you ever faced that problem and do anyone give me some advices for that issue

    Thanks!


    Nghia Luu


  2. #2
    Senior Tech 100+ Posts
    Join Date
    Dec 2007
    Posts
    171
    Post Thanks / Like
    Rep Power
    15

    Re: iRAC9065PRO, E002-0102

    I have an identical machine at the moment with exactly the same fault as yours, I have eliminated lower heater (swapped unit from identical machine) fault is still there, have replaced AC Driver board, DC-Con and checked everything else as listed in the service manual. Will be interested to know other peoples thoughts on this one...


  3. #3
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,076
    Post Thanks / Like
    Rep Power
    153

    Re: iRAC9065PRO, E002-0102

    check the printer (machine side) contacts (pins)

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Field Supervisor 500+ Posts


    Herrmann's Avatar
    Join Date
    Jan 2006
    Location
    Germany, NorthRhine Westfalia
    Posts
    736
    Post Thanks / Like
    Rep Power
    26

    Re: iRAC9065PRO, E002-0102

    Maybe the lower lamp is working and one of the lower thermistors gone bad, did you try to change the pressure crossmember assy, FM3-4835-000 ?

    If sometimes you feel a little useless, offended and depressed always remember that you were once the fastest and most victorious sperm of hundreds of millions!

  5. #5
    Senior Tech 100+ Posts
    Join Date
    Dec 2007
    Posts
    171
    Post Thanks / Like
    Rep Power
    15

    Unhappy Re: iRAC9065PRO, E002-0102

    Quote Originally Posted by Herrmann View Post
    Maybe the lower lamp is working and one of the lower thermistors gone bad, did you try to change the pressure crossmember assy, FM3-4835-000 ?
    We tried a complete fixing assembly from a working machine, still got the fault on the replacement unit...


  6. #6
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,076
    Post Thanks / Like
    Rep Power
    153

    Re: iRAC9065PRO, E002-0102

    Quote Originally Posted by seniortech View Post
    We tried a complete fixing assembly from a working machine, still got the fault on the replacement unit...
    that still does not mean the machine side connectors are ok-----

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  7. #7
    Senior Tech 100+ Posts
    Join Date
    Dec 2007
    Posts
    171
    Post Thanks / Like
    Rep Power
    15
    Will check the machine side connectors tomorrow, will let you know


  8. #8
    Field Supervisor 500+ Posts


    Herrmann's Avatar
    Join Date
    Jan 2006
    Location
    Germany, NorthRhine Westfalia
    Posts
    736
    Post Thanks / Like
    Rep Power
    26

    Re: iRAC9065PRO, E002-0102

    Check ac driver pcb, connector J810, pin 1 and 4, this is the connector that drives the lower heater lamp. ohm it out, there should be a value between 3 and 10 ohms if the connection to the lamp is existant. You should also be able to meter a value of 220 volts (in europe) if the mashine is connected to main power and fired up

    Last edited by Herrmann; 08-07-2012 at 11:00 PM. Reason: typo
    If sometimes you feel a little useless, offended and depressed always remember that you were once the fastest and most victorious sperm of hundreds of millions!

  9. #9
    Trusted Tech 50+ Posts
    Join Date
    Jan 2008
    Posts
    67
    Post Thanks / Like
    Rep Power
    14

    Re: iRAC9065PRO, E002-0102

    Hi All, Luckily, my case has been resolved after 1 day-effort. The reason is thermoswitch(TP1). The machine did not display error exactly so make me to go wrong direction. Firstly, when the error occur, I checked temperature by service mode: Display>Analog>Fix-LC, Fix-LE, Fix-LE2 They were always under 70oC (it must be 100oC) so I thought about halogen lamp and take it out from machine. I touched on it and did not feel warm It means that the lamp was not on during machine up. I removed fixing frame and rechecked thermal switch. I found that it was disconnected. The thermoswicth is sitting on fixing frame, so if we replace both lower and upper fixing unit the problem still exists. Lastly, if the machine displays E004 then I did not waste time such so much. Something to share with you Nghia Luu

    Attached Images Attached Images

  10. #10
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,076
    Post Thanks / Like
    Rep Power
    153

    Re: iRAC9065PRO, E002-0102

    (:>)

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here