Results 1 to 10 of 10
  1. #1
    Defective Technician
    Join Date
    Jun 2008
    Location
    Long Island
    Posts
    30
    Post Thanks / Like
    Rep Power
    14

    iR 2880i E00045-0000

    Machine was throwing this code and I was able to get it to work by pressing in on the bottom of the door, so I checked the door and found a bent hinge and broken pivot. After replacing them it started to work until I opened and closed the door, then it coded out. I've spent a couple of hours adjusting the OHP sensor and reflector with no luck. Using a digital camera as per the tech pub I can see the sensor emitting at initial rotation. I'm considering replacing the door,but maybe I'm missing something? Any help would be appreciated, thanks.



  2. #2
    Field Supervisor 2,500+ Posts


    zoraldinho's Avatar
    Join Date
    Mar 2008
    Posts
    2,970
    Post Thanks / Like
    Rep Power
    52

    Re: iR 2880i E00045-0000

    Are you talking about front or right door?

    A little knowledge is a dangerous thing

    Click here to be sure



  3. #3
    Defective Technician
    Join Date
    Jun 2008
    Location
    Long Island
    Posts
    30
    Post Thanks / Like
    Rep Power
    14

    Re: iR 2880i E00045-0000

    Quote Originally Posted by zoraldinho View Post
    Are you talking about front or right door?
    Right Door where the OHP Reflector is located


  4. #4
    Senior Tech 100+ Posts its_just_a_copier's Avatar
    Join Date
    May 2011
    Location
    NY
    Posts
    133
    Post Thanks / Like
    Rep Power
    0

    Re: iR 2880i E00045-0000

    I've seen this problem several times. If you can't adjust that door it must be twisted beyond repair, replacing it is the only option!

    Make sure the reflector (on the copier side) is not knocked out, and you CAN install it upside down which will cause E045.....did that before as well~!


  5. #5
    Defective Technician
    Join Date
    Jun 2008
    Location
    Long Island
    Posts
    30
    Post Thanks / Like
    Rep Power
    14

    Re: iR 2880i E00045-0000

    Quote Originally Posted by its_just_a_copier View Post
    I've seen this problem several times. If you can't adjust that door it must be twisted beyond repair, replacing it is the only option! Make sure the reflector (on the copier side) is not knocked out, and you CAN install it upside down which will cause E045.....did that before as well~!
    You mean the sensor on the machine side right? The reflector is in the door. You've replaced a door before?


  6. #6
    Field Supervisor 500+ Posts



    Join Date
    Apr 2009
    Location
    London
    Posts
    813
    Post Thanks / Like
    Rep Power
    27

    Re: iR 2880i E00045-0000

    I always thought 045 meant the sensor in the machine.

    Quote Originally Posted by Hose1cook View Post
    Machine was throwing this code and I was able to get it to work by pressing in on the bottom of the door, so I checked the door and found a bent hinge and broken pivot. After replacing them it started to work until I opened and closed the door, then it coded out.
    There is a screw in the hinge area that you replaced that strips the thread in the door. Common issue on this model. You can often verify this by pressing on the door and looking for movement. This stripped thread can also cause the manual feed to malfunction.


  7. #7
    Senior Tech 100+ Posts its_just_a_copier's Avatar
    Join Date
    May 2011
    Location
    NY
    Posts
    133
    Post Thanks / Like
    Rep Power
    0

    Re: iR 2880i E00045-0000

    Quote Originally Posted by Hose1cook View Post
    You mean the sensor on the machine side right? The reflector is in the door. You've replaced a door before?
    Usually the sensor in the door could be dirty or blocked somehow, but the common culprit is the reflector in the machine side gets knocked out.

    Yeah I've had to replace the door before for this, they are crap and get twisted easily!


  8. #8
    Field Supervisor 2,500+ Posts


    zoraldinho's Avatar
    Join Date
    Mar 2008
    Posts
    2,970
    Post Thanks / Like
    Rep Power
    52

    Re: iR 2880i E00045-0000

    Measures against increased load at closing the right door

    door.JPG

    The largest force for the operation of closing the right door is required at shutting the door at the end. This force
    of shutting the door is similar regardless of with and without the right door pressure aux. unit . Therefore, there
    is no negative effect by discontinuing the use of the right door pressure aux. unit . One side of the right door
    may not close without the right door pressure aux. unit , however, there is no problem because the door
    detection function generates recovery message.

    Servicing Work:


    If the above symptom occurs, perform the following step 1 and 2;
    1.Detach the right door pressure aux. unit (FM3-0008) [1].
    2.Remove the parts a, b, c from the detached right door pressure aux. unit (FM3-0008) [1] and then attach the unit
    to the machine again.
    a.Arm press plate (FC7-6990-000)
    b.Arm link plate (FL2-4482-000)
    c.M10 stepped screw (FU5-9350-000)
    These 3 parts maintain the strength of the machine.

    The operation procedure is attached.

    Procedure.pdf


    A little knowledge is a dangerous thing

    Click here to be sure



  9. #9
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    12,707
    Post Thanks / Like
    Rep Power
    164

    Re: iR 2880i E00045-0000

    Hate that door/ usually frustrated customers cause hinge damage-

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  10. #10
    Defective Technician
    Join Date
    Jun 2008
    Location
    Long Island
    Posts
    30
    Post Thanks / Like
    Rep Power
    14

    Re: iR 2880i E00045-0000

    Thanks everyone for your help. Replacing the Door Assm fixed it.


Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here