Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7
  1. #1
    Service Manager 1,000+ Posts
    repost for pmailfl

    charm5496's Avatar
    Join Date
    Apr 2008
    Posts
    2,388
    Rep Power
    64

    repost for pmailfl

    pmailfl

    7095 With A1 Perfect Binder Won't Print


    My 7095 with V2 Saddle Stitcher worked fine.

    Installed the Perfect Binder and when attempting to make a copy, the finisher constantly cycles, display on 7095 cycles back and forth between suspended and waiting to print, but never pulls paper. The machine recognizes both the A1 and the V2, and in the correct sequence. Machine warms up, then goes into ready mode. No errors, no limited functions.

    The tech left without an answer, but so far we have:

    1) Made sure the thin-net cables are seated properly and terminated on both the finisher and host machine (and tried both combos of having 2 T-s with a terminator at the Perfect Binder and just a T with the host signal going in and finisher going out).

    2) Checked and reseated the stapler cartridge.

    3) Shutdown the machine properly -- Held power on touch screen until Shutdown sequence came up, waited 5-6 minutes, powered off host machine), shut down A1 & V2, then powered back on in reverse order.

    4) Tried the reverse of #3.

    5) Tried unplugging everything from the wall as well.

    All of the DIP Switches in the PB are off, the V2 was left alone (as it worked before). No error codes come up.

    Any ideas on what to do next?
    Accidents don't just happen. They must be carelessly planned.

  2. #2
    Service Manager 1,000+ Posts
    repost for pmailfl

    charm5496's Avatar
    Join Date
    Apr 2008
    Posts
    2,388
    Rep Power
    64

    Re: repost for pmailfl

    did you go into service mode and tell the machine that the perfect binder is now in-between the main unit and the finisher?
    also you could have a firmware conflict depending on the level your copier and finisher are at compared to the level the perfect binder is at.
    Accidents don't just happen. They must be carelessly planned.

  3. #3
    teacher-guide-expert-guru 2,500+ Posts
    repost for pmailfl

    zoraldinho's Avatar
    Join Date
    Mar 2008
    Location
    SVN
    Posts
    4,943
    Rep Power
    106

    Re: repost for pmailfl

    Charm's back!

    welcome.jpg
    Practice makes perfect
    If it ain't broke, don't fix it
    A picture is worth a thousand words
    If you want something done right, you have to do it yourself


  4. #4
    Technician
    Join Date
    May 2009
    Posts
    35
    Rep Power
    31

    Re: repost for pmailfl

    Quote Originally Posted by charm5496 View Post
    did you go into service mode and tell the machine that the perfect binder is now in-between the main unit and the finisher?
    also you could have a firmware conflict depending on the level your copier and finisher are at compared to the level the perfect binder is at.
    Yes, the perfect binder is setup as 1, the finisher as 2, on system monitor when trying to print, it shows the devices in the correct order.

    Not sure about firmware or how to check.

  5. #5
    Service Manager 1,000+ Posts
    repost for pmailfl

    charm5496's Avatar
    Join Date
    Apr 2008
    Posts
    2,388
    Rep Power
    64

    Re: repost for pmailfl

    Quote Originally Posted by zoraldinho View Post
    Charm's back!

    welcome.jpg
    never really went away....just been busy as all heck!!!!!
    Accidents don't just happen. They must be carelessly planned.

  6. #6
    Service Manager 1,000+ Posts
    repost for pmailfl

    charm5496's Avatar
    Join Date
    Apr 2008
    Posts
    2,388
    Rep Power
    64

    Re: repost for pmailfl

    Quote Originally Posted by pmailfl View Post
    Yes, the perfect binder is setup as 1, the finisher as 2, on system monitor when trying to print, it shows the devices in the correct order.

    Not sure about firmware or how to check.
    you need to get into service mode and check what versions your machine, binder and finisher are reading. If upgrade is needed you will need the downloader PCB to connect the binder to your laptop to install the firmware.

    service mode>copier>display>version
    Accidents don't just happen. They must be carelessly planned.

  7. #7
    Technician
    Join Date
    May 2009
    Posts
    35
    Rep Power
    31

    Re: repost for pmailfl

    Quote Originally Posted by charm5496 View Post
    you need to get into service mode and check what versions your machine, binder and finisher are reading. If upgrade is needed you will need the downloader PCB to connect the binder to your laptop to install the firmware.

    service mode>copier>display>version
    DC_CON 20.21
    R-Con 2.03
    Panel 00.03
    Feeder 4.01
    Sorter 20.08
    NIB 5.00
    MN_Cont 77.03

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here