Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Service Manager 250+ Posts tinnyjay's Avatar
    Join Date
    Oct 2009
    Location
    Tirana
    Posts
    496
    Post Thanks / Like
    Rep Power
    0

    What causes this please?

    Hello
    Canon CLC3200 with good drums,new fuser and a low meter ITB give this on paper.
    I think is ITB cleaning blade but i need your opinion to be sure :
    1212.jpg

    "Who loves the roses,must also bear thumbs"

  2. #2
    Field Supervisor 2,500+ Posts


    zoraldinho's Avatar
    Join Date
    Mar 2008
    Posts
    2,941
    Post Thanks / Like
    Rep Power
    51

    Re: What causes this please?

    Semething slide on ITB belt and blurring image before fuser(protective cover or peace of paper). Drums and cleaning belt are OK.

    Last edited by zoraldinho; 09-22-2012 at 01:09 PM.
    A little knowledge is a dangerous thing

    Click here to be sure



  3. #3
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    11,644
    Post Thanks / Like
    Rep Power
    146

    Re: What causes this please?

    Quote Originally Posted by tinnyjay View Post
    Hello
    Canon CLC3200 with good drums,new fuser and a low meter ITB give this on paper.
    I think is ITB cleaning blade but i need your opinion to be sure :
    1212.jpg



    remove the ITB unit / then remove the underside plates/

    clean the small one / throw the Large one in the Garbage>

    re-attach the small plate as shown in picture below- click to enlarge pic

    u need to put back the varistor as shown / wedge other end under that metal leaf spring/

    Attached Images Attached Images
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  4. #4
    Banned 250+ Posts
    Join Date
    Mar 2009
    Location
    London, UK
    Posts
    342
    Post Thanks / Like
    Rep Power
    0

    Re: What causes this please?

    Yeah this is very common.
    Remove & clean both the underside plates. Personally I fit the large one back as it protects the belt when you remove the ITB unit, without it the belt can get damaged when you or the next engineer places the unit down.



  5. #5
    Service Manager 250+ Posts tinnyjay's Avatar
    Join Date
    Oct 2009
    Location
    Tirana
    Posts
    496
    Post Thanks / Like
    Rep Power
    0

    Re: What causes this please?

    the plate was dirty and i am getting an E020-01d0 which means :
    The supply of toner for the toner
    container to the developing assembly
    has failed. The toner
    cartridge motor fails to rotate.
    The toner container is empty.
    The toner supply mouth of the
    drum unit is damaged. The ATR
    sensor has an open circuit.
    For the first 2 digits of detail
    code xxEE,
    xx=00: fault in access to drum
    unit
    xx=01: fault in access

    Yellow drum is new toner is full and doesnt have any braked part,but this problems never stops "Printer is warming up"
    Any idea?

    I put another yellow drum with 344 life and copier is ok,but when i put the new one,Density is -4.55

    Last edited by tinnyjay; 09-23-2012 at 12:17 PM.
    "Who loves the roses,must also bear thumbs"

  6. #6
    Banned 250+ Posts
    Join Date
    Mar 2009
    Location
    London, UK
    Posts
    342
    Post Thanks / Like
    Rep Power
    0

    Re: What causes this please?

    Check the DENS level of the yellow confirm that it is -4-5%

    Check the operation of the drum & toner shutters

    If you have a brand new yellow toner fit this & see if the yellow DENS returns to normal (about 0.0%)



  7. #7
    Service Manager 250+ Posts tinnyjay's Avatar
    Join Date
    Oct 2009
    Location
    Tirana
    Posts
    496
    Post Thanks / Like
    Rep Power
    0

    Re: What causes this please?

    Quote Originally Posted by Canon.Tech View Post
    Check the DENS level of the yellow confirm that it is -4-5%

    Check the operation of the drum & toner shutters

    If you have a brand new yellow toner fit this & see if the yellow DENS returns to normal (about 0.0%)

    Everything is new,but density is about -5.00

    "Who loves the roses,must also bear thumbs"

  8. #8
    Banned 250+ Posts
    Join Date
    Mar 2009
    Location
    London, UK
    Posts
    342
    Post Thanks / Like
    Rep Power
    0

    Re: What causes this please?

    Have you fitted a new yellow toner AFTER you got the error code?

    Than dens level of -5% means there isn't enough yellow toner in the drum unit


  9. #9
    Field Supervisor 5,000+ Posts


    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    11,644
    Post Thanks / Like
    Rep Power
    146

    Re: What causes this please?

    Quote Originally Posted by tinnyjay View Post
    Everything is new,but density is about -5.00
    REMOVE all DRUMS & TONER UNITS & ITB UNIT >
    u then need to Look in towards back frame at YELLOW unit AREA > to see if any of the white drive couplings/gears have popped off the Motors below--

    Motor M20=toner container motor (Y)=stirs toner inside the toner container (Y)


    M12=developing motor (Y)=drives the developing unit (Y).



    +++++++++++++++++see below
    xx=01: Y xxD0
    The supply of toner for the toner container to the developing assembly has failed. //

    The toner cartridge motor fails to rotate.//The toner container is empty.
    The toner supply mouth of the drum unit is damaged. // The ATR sensor has an open circuit.


    If the drum units have been removed repeatedly without the drum guide service tool it's possible to break one or both tabs (see picture below). These tabs open the toner hopper when the drum unit is slid in, and if they are broken, toner will not be fed into the drum unit.
    NOTE: The unit may work for a while until the developer to toner ratio drops enough to cause an error.



    drum.JPG

    Attached Images Attached Images
    Last edited by teckat; 09-23-2012 at 03:53 PM.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  10. #10
    Service Manager 250+ Posts mramlawi's Avatar
    Join Date
    Jul 2011
    Posts
    384
    Post Thanks / Like
    Rep Power
    9

    Re: What causes this please?

    ITB check it

    Distinguished road makes you jewel in rough

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here