Canon CLC3220 C1 won't boot after update

[mata]

Hi guys. I need a small help on this one.
The customer gets a used CLC 3220 vith C1 fiery both the machine and fiery on german. There was not any other language installed on machine. So i hooked up with SST to update language and when I was there update rest of the system. Only thing that was updated was DCON and language since other was up to date. I also reinstall fiery software to get it on english. All went ok. After I turned machine on the fiery won't boot. I get a setup screen, it passes all diagnostic, clear server done, but when it continue boot ( wait a moment...blah blah) it goes shut down. I never before seen that screen that says fiery is going shut down and turn it off on backside of machine.
When compare P-print before and after update, only difference was DCON from some old version to fresh 38.02 and english 90.03. I tried to change IMG-CONT to 0 and back to 3 but nothing changes. I pull out fiery and both boards and take it to other 3220 and get choose language screen on fiery. So here it works fine. On this machine DCON ver is 37.XX ( i didn't remember number), and everything else is the same. When I get it back it goes down.
What can be the reason to fiery shut down?

PS Sorry for my bad english. Cheers

[Fer]

So the Fiery works fine on another 3220? What is the fw version on that machine, i mean mcon version. I remeber that C1 with fw 1.x only worked with machine mcon lower as 50.xx. If you have mcon +50 than u need C1 with FW 2.0

Did u try to reseat the interface card in the mcon?

Btw, these machines ROCK. Color is on par with Advance C70xx and once serviced on with 4M on the counter, still spotless.

[mata]

Hi Fer. Thanks for reply.
Fiery is C1v2. On both machines MCON is the same ver.
They certainly rocks. This machine is 250k so it would be shame dump it.

Hm. I just realize that I was wrong. The machine with non working fiery is CLC 2620, so thread name is wrong. But I think it's the same software and that isn't matter. Also SST allows me to upload the software. So on the 2620 with DCON 38.02 it won't boot and in the 3220 with DCON 37.XX it works just fine.

Cheers

[Fer]

Swap/reseat the cable and interface card

[teckat]

Hi Fer. Thanks for reply.
Fiery is C1v2. On both machines MCON is the same ver.
They certainly rocks. This machine is 250k so it would be shame dump it.

Hm. I just realize that I was wrong. The machine with non working fiery is CLC 2620, so thread name is wrong. But I think it's the same software and that isn't matter. Also SST allows me to upload the software. So on the 2620 with DCON 38.02 it won't boot and in the 3220 with DCON 37.XX it works just fine.

Cheers

follow this exactly
If your Fiery has a power SW>turn it off---
1- Now Remove all connections from C1/C2 Fiery to printer (interface cable-& cross-cable) + unplug it's power cord-
2-Enter Service mode (Additional Functions > 2 & 8 > Additional Functions).
Select Copier > Option > INT-FACE > IMG-CONT.
Change this setting from "3" to "0" and press OK.
Power Cycle off the imageRUNNER.
3-Now Before Making any Connections /
4-Power Cycle on the imageRUNNER.
5-Re-Enter Service mode (Additional Functions > 2 & 8 > Additional Functions).
Select Copier > Option > INT-FACE > IMG-CONT.
Change back this setting from "0" to "3" and press OK./now exit from the Service Mode
6-Do a proper shutdown on control panel >Now> Turn off the control panel power switch./then Turn off the main power switch.
7-Disconnect the Printer power cable (from the wall/floor outlet).
8-Next> connect the I/F cable from Fiery to Printer side-
9-Connect the Cross-Over cable from Fiery to Printer
10-Connect Network cable from Fiery to wall Network connection
11-Connect the Fiery Power Cable to wall outlet-
12-Plug in 3220 Printer power cable back into to wall outlet
13-Put Fiery power SW on if on C1/C2 box> Now Power up 3200 Printer
14-Follow any OFF/ON prompts if shown on LCD Control panel
15-Hopefully u should be able to re-due you printer settings

At the Control Panel, press [Printer]tab. Press [Printer Status/Settings].
at Password prompt-use Fiery.1 then continue with set up

Note: always use the shutdown procedure for Printer on Control panel> follow the prompts>
never just reach over and flip off the Main Printer switch

[Herrmann]

Teckat is right, try this first. If that does not work, i would suggest you to dowmgrade to an earlier Firmwre Version

[Fer]

I don;t remember the 3200 series having a proper shutdown, only for the Fiery itself there is one in the printer menu.

[teckat]

I don;t remember the 3200 series having a proper shutdown, only for the Fiery itself there is one in the printer menu.

How to properly shut down the imageRUNNER-iR Series and imagePRESS Series machines

These models have a Shutdown Mode function that should be used before powering off the machine. Shutting the machine down properly will help protect the data on the machine's hard drive. Use the following procedure:

1. Enter Shutdown Mode by either of the following methods:

I - Press Additional Functions > Common Settings > Shut Down Mode.
or
II - Hold down the ON/OFF Power button on the machine's control panel for 5 seconds (NOT the ON/OFF Power switch on the side of the machine's main body).

2. The Shutdown Mode screen will appear on the machine's LCD screen. It will display the processes currently running on the machine.

3. Press the Start button on the LCD screen (lower corner of display)to begin the shutdown process.
4. Wait until the shutdown process finishes. When it is finished, the following message will be displayed:

'Turn OFF the Main Power Switch (on the main unit's right side).'

----------------------------------------------------------------------------------------------------
* Forced Off Option - If the shutdown process is taking too long and you must power down the machine as soon as possible, you can hit the Forced Off button on the LCD screen. This will stop the finishing process of the hardware and/or updating of the device data. The 'Turn Off the main power switch (on the main unit's right side)' message will appear almost immediately. THIS IS NOT RECOMMENDED.

It is best to let the shutdown process finish before powering off the main unit.

* The newer machines will power off themselves at the end of this process. There is no need to use the power switch on the side of the machine's main body to power down the unit.

5. Turn off the ON/OFF switch on the side of the machine's main body to power down the unit.

[KL568]

Hi, Teckat

Able to share with us any Servcie Mode settings to enable the Shutdown mode for iRC32xx? Seems like our region don't have it as default. Thanks in advance.

[teckat]

Hi, Teckat

Able to share with us any Servcie Mode settings to enable the Shutdown mode for iRC32xx? Seems like our region don't have it as default. Thanks in advance.

Sorry , to mislead but the
Common Settings > Shut Down Mode
is in 5180 series/
---------------------------------------------------
& also Control Panel Power Switch method
Press to turn the control panel ON or OFF. When
the control panel power switch is held for more
than three seconds, it initiates the Shutdown
mode.
-------------------------------------------------------

Trying to remember all these differant shut down procedures/ drives me nuts----------

Believe on the 3200/3220----------
If you want to turn the main power OFF, u should first turn the control panel power ON/OFF switch
OFF, and then press the main power switch on machine side.



sorry for the confusion
getting a little brain freeze at my age


of course with a Fiery/ u always use inside the Printer tab menu to shut down from there--