IRC3220 with DADF-K1 issue

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • wagsmd
    Technician
    • Jan 2011
    • 14
    #1

    IRC3220 with DADF-K1 issue

    Looking for some expertise. Working on a IRC3220 with a DADF-K1. For some reason the feeder does not respond and doesn't appear in options area of the service menu. Can't seem to get the feeder to respond to anything. Anyone with any ideas or thoughts? Thanks in advance for any help.
    Tags: None
    • SCREWTAPE
      East Coast Imaging

      Site Contributor
      2,500+ Posts
      • Jan 2009
      • 3396
      #2
      Re: IRC3220 with DADF-K1 issue

      Originally posted by wagsmd
      Looking for some expertise. Working on a IRC3220 with a DADF-K1. For some reason the feeder does not respond and doesn't appear in options area of the service menu. Can't seem to get the feeder to respond to anything. Anyone with any ideas or thoughts? Thanks in advance for any help.
      Did you check for any error codes in your error history under service mode.

      E400-xxxx are usually associated with feeder issue.

      Sounds like a power/communication issue.

        Comment

        • teckat
          Field Supervisor

          Site Contributor
          10,000+ Posts
          • Jan 2010
          • 16083
          #3
          Re: IRC3220 with DADF-K1 issue

          Originally posted by wagsmd
          Looking for some expertise. Working on a IRC3220 with a DADF-K1. For some reason the feeder does not respond and doesn't appear in options area of the service menu. Can't seem to get the feeder to respond to anything. Anyone with any ideas or thoughts? Thanks in advance for any help.
          DF is not under OPTION/<BODY>MODEL-SZ for DF is thereshould be there 0: AB (6R5E) 1: INCH (5R4E)
          2: A (3R3E) 3: AB/INCH (6R5E)
          U should see DF FIRMWARE ver in service mode -COPIER>DISPLAY>Version??
          DC-CON
          ROM version of DC controller PCB.
          R-CON
          ROM version of reader controller PCB.
          PANEL
          ROM version of control panel CPU PCB.
          ECO
          ROM version of ECO PCB.
          FEEDER
          ROM version of DADF controller PCB.

          what does it show on P PRINT ??


          ???- did it ever work?
          Check if The input voltage of 24V DC is present on J2 pin 3 on ADF Controller.

          Ensure that the ADF open / close sensor (SR6) actuator is functioning properly. Also make sure that the platen cover socket blanking sheets are there-
          It is possible during installation or during servicing that the right hinge of the DADF K1 may not be seated properly, or may be deformed causing the DADF closed sensor actuator to not make contact with the machine when closed, (See picture below). This will result in the machine not seeing the feeder closed and thereby will not detect an original that has been placed.



          did someone remove & reconnect that square interface DF PLUG while printer was on ??

          DF PLUG.JPG

          1- what happens when u place sheet paper in DF TRAY ?
          >does the paper present LED illuminate ?
          Attached Files
          **Knowledge is time consuming, exhausting and costly for a trained Tech.**

            Comment

            • Canon.Tech
              Trusted Tech
              • Mar 2009
              • 335
              #4
              Re: IRC3220 with DADF-K1 issue

              Also in the pic above that teckat posted, that connector gets knocked & broken visually check for damage or take the cover off & check the cables.

                Comment

                • wagsmd
                  Technician
                  • Jan 2011
                  • 14
                  #5
                  Re: IRC3220 with DADF-K1 issue

                  Thanks for the info and ideas. The feeder did work but they say it hadn't been used in a while. Couldn't tell you if it was unplugged while it was powered up. That unit i over in Lincoln so I will have to follow up on it when I am over there later in the week and then post back if we still don't have it figured from all your ideas and suggestions. As always, you guys are great. Thanks again.

                    Comment

                    Previous template Next
                    Working...