canon ir 3225 no display

[pramod]

Hello Every One,

I have two machines canon ir 3225, and one of them is dead. no display ,except mother board i cross checked all pcbs . Should i connect mother board directly ?
please tell me procedure how to check main boad.

[doktor]

Review and use.
IR3235 Canon

[spectraindo]

Check the Memory DIMM on the Mainboard, Remove - Clean and Place on the Mainboard it again.
If you have another machine ,try switching the Memory DIMM.

[pramod]

Hi,
thanks for reply
i already checked memory DIMM .but no use , machine is in dead position . Please tell me can i check main board on other machine directly because there is machine id pcb is mounted on it

[teckat]

Hi,
thanks for reply
i already checked memory DIMM .but no use , machine is in dead position . Please tell me can i check main board on other machine directly because there is machine id pcb is mounted on it

================================================

Explain DEAD

1-NO POWER TO PRINTER AT ALL=NO WARM UP/NO START UP
2-HAVE POWER LIGHT INDICATOR ON PANEL > BUT LCD SCREEN IS BLANK/BLACK (Blank Display With a Green LED is Occurring) ?
3-No Display, Green Power Indicator is ON and Main Controller LEDs are Off = yes or no

The control panel display is off and the green power indicator lamp is on. On the Main Controller all LED lamps are off. The AC Driver is missing 120 VAC output from connectors J475 and J476.



Solution :
Replacing the Main Controller resolved the problem.

---

-did u try re-seating the LCD control panel.

--------------------------
IF U ARE NOT A TECH> do not perform the following> call for service

If the Main Controller "registered value" ID does not match the REAL TIME CLOCK (RTC) ID, the Main Controller Malfunctions; preventing the LCD display from powering up or no power to unit.

By shorting JP1 on the Main Controller it will clear the RTC "registered value", to correct the ID between the Main Controller and RTC Circuit.

Procedure:
1. Turn OFF the Main Unit.
2. Either unplug the power cord from the wall.
3. Remove the rear cover of the Main Unit.
4. Below the left leg of the Battery, jump JP1 for 3-5 seconds.
5. Plug in the power cord and turn on the Main Unit.
6. Verify that the Main Unit powers ON and that the LCD display works.
7. Re-install the rear cover.

[teckat]

The imageRUNNER does not cycle and has a blank display with the green LED on. yes or no




If this issue occurs, check to see if any of the LEDs on the Main Controller are lit.
If none of the LEDs are lit, replace the Main Power Supply PCB Assembly. The part number for the Main Power Supply PCB Assembly is FM3-6145-000.

[campy]

I just had this a couple of weeks ago and it was a faulty main controller. Does the finisher cycle when turning on the copier? If not it's the board. The repair cost at NSRW is $390.

[Deepaklohmi]

[QUOTE=teckat;348086]================================================

Explain DEAD

1-NO POWER TO PRINTER AT ALL=NO WARM UP/NO START UP
2-HAVE POWER LIGHT INDICATOR ON PANEL > BUT LCD SCREEN IS BLANK/BLACK (Blank Display With a Green LED is Occurring) ?
3-No Display, Green Power Indicator is ON and Main Controller LEDs are Off = yes or no

The control panel display is off and the green power indicator lamp is on. On the Main Controller all LED lamps are off. The AC Driver is missing 120 VAC output from connectors J475 and J476.



Solution :
Replacing the Main Controller resolved the problem.

---

476 475 Have 130 Volt and out from J691 is 3.5 v butno power then

[teckat]

[QUOTE=Deepaklohmi;2457308]

================================================

Explain DEAD

1-NO POWER TO PRINTER AT ALL=NO WARM UP/NO START UP
2-HAVE POWER LIGHT INDICATOR ON PANEL > BUT LCD SCREEN IS BLANK/BLACK (Blank Display With a Green LED is Occurring) ?
3-No Display, Green Power Indicator is ON and Main Controller LEDs are Off = yes or no

The control panel display is off and the green power indicator lamp is on. On the Main Controller all LED lamps are off. The AC Driver is missing 120 VAC output from connectors J475 and J476.



Solution :
Replacing the Main Controller resolved the problem.

476 475 Have 130 Volt and out from J691 is 3.5 v butno power then

--------------------------------------------------------------------------------------------------

where have u been since 2013