Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 4 of 4
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Jan 2009
    Location
    Moscow
    Posts
    70
    Rep Power
    18

    Booklet Finisher-D1

    Greetings to all.

    Problem with Booklet Finisher-D1 (iR ADV 8105).

    Stapling on corners - OK, the brochure - OK. Double stapling - only one back staple is present. The front staple is not present.

    Codes of errors and jams in history are not present. The device worked without problems till the moment of replacement of a stapler unit (there was error Е532). After replacement some times double stapling was normal. There was a problem...

    The system has been updated: MN - v46.02, FIN_CON - v33.01. What could happen?

    Any ideas are accepted with gratitude..

    Victor V

    Hardworking people are not present. Simply many it is boring to idle.

  2. #2
    Field Supervisor 500+ Posts
    Join Date
    Jun 2012
    Location
    Bundaberg Qld.
    Posts
    608
    Rep Power
    19

    Re: Booklet Finisher-D1

    Quote Originally Posted by victor_v View Post
    Greetings to all.

    Problem with Booklet Finisher-D1 (iR ADV 8105).

    Stapling on corners - OK, the brochure - OK. Double stapling - only one back staple is present. The front staple is not present.

    Codes of errors and jams in history are not present. The device worked without problems till the moment of replacement of a stapler unit (there was error Е532). After replacement some times double stapling was normal. There was a problem...

    The system has been updated: MN - v46.02, FIN_CON - v33.01. What could happen?

    Any ideas are accepted with gratitude..

    Victor V
    G'day mate, I am assuming the Corner, Brochure & Double Stapling, is OK from Tray 1 (A) and/or Tray2 (B) - right?

    I am thinking the problem is from Saddle Stitching which comes out of the Bottom Tray - if so pull the lower Drawer Section out & check the Staple Cartridges to ensure they both have Staples present, if Staples are there/ok then check for a bent or jammed Staple in the Front Cartridge.


  3. #3
    Field Supervisor 500+ Posts vigour's Avatar
    Join Date
    Aug 2010
    Posts
    980
    Rep Power
    25

    Re: Booklet Finisher-D1

    I helped someone with this issue. In this case it would double staple sets of 20 or less.
    You can run test prints PG1 or whatever, and set FINISH to 2 ( this does double stapling).

    The solution had to do with the stapler interference sensor being blocked intermittently, when the stapler came forward.
    Watch it and Check for a broken spring or, something making it bounce.
    I think he ended up raising the stapler mount to prevent the sensor from being blocked

    Last edited by vigour; 08-10-2013 at 03:26 AM.

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    Jan 2009
    Location
    Moscow
    Posts
    70
    Rep Power
    18

    Re: Booklet Finisher-D1

    Thanks to all

    The problem was with the activator of the stapler interference sensor and springs

    Good luck

    Victor V

    Hardworking people are not present. Simply many it is boring to idle.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-=-=-=-=-=-


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here