Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 9 of 9

Thread: CANON IR 3300

  1. #1
    Senior Tech 100+ Posts sniper2g8's Avatar
    Join Date
    Jan 2013
    Posts
    108
    Rep Power
    0

    CANON IR 3300

    Please after cleaning the laser unit and changing the drum the copy is still faint pls help

  2. #2
    East Coast Imaging 2,500+ Posts
    CANON IR 3300

    SCREWTAPE's Avatar
    Join Date
    Jan 2009
    Location
    New York City
    Posts
    3,399
    Rep Power
    69

    Re: CANON IR 3300

    Quote Originally Posted by sniper2g8 View Post
    Please after cleaning the laser unit and changing the drum the copy is still faint pls help
    did you try the transfer roller?

    hvt can be a factor.
    Canon Copier Repair Service. Sales, Parts & Toner. NYC/NJ area. Contact:East Coast Imaging Solutions,LLC

  3. #3
    Senior Tech 100+ Posts sniper2g8's Avatar
    Join Date
    Jan 2013
    Posts
    108
    Rep Power
    0

    Re: CANON IR 3300

    Quote Originally Posted by SCREWTAPE View Post
    did you try the transfer roller?

    hvt can be a factor.
    I will check that tomorrow and give you the feed back

  4. #4
    Man About Town 250+ Posts CanonSco's Avatar
    Join Date
    Jul 2010
    Posts
    368
    Rep Power
    31

    Re: CANON IR 3300

    Dev handle in correct position? Dev moving over to drum correctly?
    Yes, I am a nerd.
    Gaming PC - check. Raspberry Pi - Check. Custom ROM on phone - check. Thick glasses - check.

  5. #5
    Tech Specialist 1,000+ Posts Canuck's Avatar
    Join Date
    Nov 2007
    Location
    Southwestern Ontario
    Posts
    1,713
    Rep Power
    63

    Re: CANON IR 3300

    Is dev cylinder coated with toner? How are prints from the print engine(p print for example)? If ok,look upstairs(reader). If prints light,suspect transfer as stated. Pop the roll out,clean the shaft ends where contact is made(also clean the contacts that the ends ride on). Or they poured in the wrong toner
    Last edited by Canuck; 09-18-2013 at 11:44 PM.

  6. #6
    Service Manager 1,000+ Posts
    CANON IR 3300

    Brian8506's Avatar
    Join Date
    Feb 2009
    Location
    New Jersey
    Posts
    1,588
    Rep Power
    62

    Re: CANON IR 3300

    Vacuum dv and give cylinder a good dry wiping and install fresh toner

  7. #7
    Senior Tech 100+ Posts Matoku's Avatar
    Join Date
    Feb 2008
    Location
    sabah
    Posts
    172
    Rep Power
    34

    Re: CANON IR 3300

    Quote Originally Posted by Brian8506 View Post
    Vacuum dv and give cylinder a good dry wiping and install fresh toner

    Yeh, after vecuum all the toner inside the dv tank. either using an alkohol or any else. you cleans the dv roller. makesure it dry enough and clean. top up fresh toner and runs the toner-s in function. wait until it stop then try do copy or print.

    sometime it may be the dv spacer bearing give this problem.

    Good luck.

  8. #8
    Senior Tech 100+ Posts sniper2g8's Avatar
    Join Date
    Jan 2013
    Posts
    108
    Rep Power
    0

    Re: CANON IR 3300

    Quote Originally Posted by Canuck View Post
    Is dev cylinder coated with toner? How are prints from the print engine(p print for example)? If ok,look upstairs(reader). If prints light,suspect transfer as stated. Pop the roll out,clean the shaft ends where contact is made(also clean the contacts that the ends ride on). Or they poured in the wrong toner
    the p - print is light

  9. #9
    Service Manager 10,000+ Posts
    CANON IR 3300

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: CANON IR 3300

    Quote Originally Posted by sniper2g8 View Post
    the p - print is light
    -----------------------------------------------------
    Light image on copies, prints and Test Prints ---

    If image on DRUM is Good >? see below

    Inspect & or Replace the Transport Bed Varistor FF3-1173-000


    +++++
    Copies are very faint from the Glass and on Test Prints ?

    A poor contact with the Developer Bias Tab can cause lack of Developer Bias.
    Check the Developer Bias Tab inside the machine and reform the Developer Bias Tab to better fit the Developer Unit contact.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here