IR5570 ADF PROBLEM

[COPIERTEC ASSOCIATES]

Hi, to all.I have been working on this machine but got problem when copying from the ADF.
When copying from the ADF using the A4 format the copy is ok,but when i put the copy on
the A4R format the text is cut off or goes to pick paper from the A3 cassette on auto and
still cuts off the text.Could someone assist to give proper copy settings from the ADF.
Thanks.

[blee]

Can't remember the exact location but Under the Feeder Service Mode there are TRAY-A4 and TRAY-A4R settings. Just select the service mode and then set the ADF guides to that size then push the OK in the lower right corner and machine will set the size correctly. You dont need paper in the ADF to perform this service mode, just make sure guides are set to the correct width for the mode you are performing.

[COPIERTEC ASSOCIATES]

Thanx for the quick response, i will try that when i get back to the machine and give a feed back.

[Canuck]

Yuppers...that will do it. FEEDER/FUNCTION is where its at

[COPIERTEC ASSOCIATES]

Can't remember the exact location but Under the Feeder Service Mode there are TRAY-A4 and TRAY-A4R settings. Just select the service mode and then set the ADF guides to that size then push the OK in the lower right corner and machine will set the size correctly. You dont need paper in the ADF to perform this service mode, just make sure guides are set to the correct width for the mode you are performing.

I tried this out but nothing happened,could there be a step am missing out? More ideas welcome.

[Ron314]

Here's some information from the ir5570 service manual regarding this adjustment.

16.5.2.1 FEEDER List 0009-6356iR5570 / iR6570


In service mode run through this tab sequence COPIER > FEEDER > FUNCTION till you arrive at the choices listed below. Make sure that you place the matching paper type in the feeder tray before starting the procedure. The procedure takes a few seconds so wait for it to finish.






TRY-A4

Use it to execute automatic adjustment of paper width detection
reference point 1 of the ADF original pickup tray.


TRY-A5R

Use it to execute automatic adjustment of paper width detection
reference print 2 of the ADF original pickup tray.


TRY-LTR

Use it to execute automatic adjustment of paper width detection
reference point 1 of the ADF original pickup tray.


TRY-LTRR
Use it to execute automatic adjustment of paper width detection
reference point 2 of the ADF original pickup tray.

Ron

[alexandretecnico]

verifique tambem o atuador na bandeja do adf, as vezes ele fica atuando o sensor que indentifica o A3, podendo ate ocasionar copia branca

[northernlife]

Here's some information from the ir5570 service manual regarding this adjustment.



Ron

You must perform all 4 of these adjustments. You're going to want to do a sens-init as well. And you're going to want to check how the machine is detecting originals
1. Service Mode Level 1>OPTION>BODY>MODEL-SZ>set to 1 when used in an inch environment.
2. Service Mode Level 2>OPTION>BODY>SENS-CNF>set to 1 when used in an inch environment.
3. Run the tray width adjustment for the DADF. Set a LTR paper in the DADF's original tray and set the width guides to match the LTR paper's width and run Service Mode>Feeder>Function>TRY-LTR>press OK. After this run the same adjustment for LTRR. Place a LTRR paper in the DADF's original tray and run Service Mode>Feeder>TRY-LTRR>press OK. After these adjustments have been made power cycle the machine.
4.Try initializing Common and Copy Settings in Additional Functions.

[COPIERTEC ASSOCIATES]

Thanks so much guys,i will be back on site tomorrow and will give a feedback.

[COPIERTEC ASSOCIATES]

You must perform all 4 of these adjustments. You're going to want to do a sens-init as well. And you're going to want to check how the machine is detecting originals
1. Service Mode Level 1>OPTION>BODY>MODEL-SZ>set to 1 when used in an inch environment.
2. Service Mode Level 2>OPTION>BODY>SENS-CNF>set to 1 when used in an inch environment.
3. Run the tray width adjustment for the DADF. Set a LTR paper in the DADF's original tray and set the width guides to match the LTR paper's width and run Service Mode>Feeder>Function>TRY-LTR>press OK. After this run the same adjustment for LTRR. Place a LTRR paper in the DADF's original tray and run Service Mode>Feeder>TRY-LTRR>press OK. After these adjustments have been made power cycle the machine.
4.Try initializing Common and Copy Settings in Additional Functions.

Great job done!Thanks so much Northernlife and all the members that gave in the ideas.I did the above adjustments and the machine worked.