hola a todos, la prueba 6 (test 6) esta movido el color amarillo, no registran todos los colores exactamente, hay algún tipo de ajuste o que puede estar ocasionando este problema
hola a todos, la prueba 6 (test 6) esta movido el color amarillo, no registran todos los colores exactamente, hay algún tipo de ajuste o que puede estar ocasionando este problema
En modo de servicio en COPIER--FUNCTION--LASER--LD-ADJ-Y te puede ayudar a corregir el desfase del laser para el color amarillo.
----------------
click pdf---
PG6 CHECK.pdf
The ITB home position is determined by detecting the reflecting surface on the edge of the ITB with the ITB HP lower sensor (PS101) or the ITB upper sensor (PS102) as shown in the diagram below. This is a white reflecting surface that resides on the rear underneath the ITB belt which obviously can get dirty in time. If this reflective surface is dirty, it can miscalculate the ITB home position and therefore affect the lead edge registration. Clean this reflective surface and the ITB home position sensor mentioned here.La posición inicial ITB se determina mediante la detección de la superficie reflectante en el borde de la ITB con el ITB HP sensor inferior (PS101) o el sensor superior ITB (PS102) como se muestra en el siguiente diagrama. Se trata de una superficie reflectante blanca que se encuentra en la parte trasera debajo de la cinta ITB que obviamente puede ensuciarse con el tiempo. Si la superficie reflectante se ensucia, se puede calcular mal la posición inicial ITB y por lo tanto afecta el registro del borde delantero. Limpie la superficie reflectante y el sensor de posición de reposo ITB mencionado aquí.
-------------------------------------------
Registration is Shifting in the Lead to Trail edge Direction
The magenta patch is placed on the ITB belt ahead of the image to be transferred. The patch is read by PS110, the Lead Edge detection Sensor so that it can align the paper to the image on the ITB. The Lead Edge Detection Sensor is covered by a shutter. UN219 drives the Leading Edge Patch Detecting Shutter.El registro se está desplazando en el plomo en Trail Dirección borde
El parche de color magenta se coloca sobre la cinta ITB por delante de la imagen a ser transferida. El parche es leído por PS110, el sensor de detección del borde de avance de modo que pueda alinear el papel de la imagen en la ITB. El sensor de detección del borde de avance está cubierto por un obturador. UN219 impulsa el Patch Leading Edge Detección de obturación.
Compruebe PS110 para asegurarse de que está limpio y que el obturador se abre completamente. En este caso, en sustitución de PS110 del sensor de detección de borde delantero y UN219 puede resolver el problema.
Check PS110 to make sure it is clean and that the shutter is opening all the way. In this case, replacing PS110 the Lead Edge Detection Sensor and UN219 can resolve the issue.
-----------------------------------------------------------------------------------------------------
On system software version 10.15 for the imagePRESS C7000VP Series, a new service mode was introduced that can assist in image quality issues to determine whether the problem is coming from the image process unit or the laser. The following service mode setting COPIER > FUNCTION > MISC-P > GRID-ADJ will print out a 4 color grid on one 11X17 sheet. This test page is executed via analog development which means it does not use the lasers. This is a convenient tool to determine if the image quality issue at hand is caused by development or it is a laser problem. Below is a sample of the grid that prints on the 11X17 showing bands of all 4 colors on a single 11X17.El software del sistema versión 10.15 de la Serie imagePRESS C7000VP, un nuevo modo de servicio se introdujo que puede ayudar en los problemas de calidad de imagen para determinar si el problema proviene de la unidad de proceso de imagen o el láser. El siguiente servicio de modo de ajuste COPIADORA> Funcionamiento> MISC-P> RED-ADJ imprimirá una cuadrícula de color 4 en una hoja 11X17. Esta página de prueba se ejecuta a través del desarrollo análogo que significa que no utiliza el láser. Esta es una herramienta conveniente para determinar si el problema de calidad de imagen a la mano es causada por el desarrollo o es un problema láser. A continuación se muestra un ejemplo de la red que se imprime en las bandas que muestran 11X17 de los 4 colores en un solo 11X17.
Nota: Debe establecer Cajón 1 de 11X17 y asignar el papel normal de tipo de papel o bien un NG mostrará.
Note: You must set Drawer 1 to 11X17 and assign the paper type PLAIN Paper or else an NG will display.
**Knowledge is time consuming, exhausting and costly for a trained Tech.**
Bookmarks