Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 5 of 5
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    Sep 2012
    Location
    cape town
    Posts
    69
    Rep Power
    24

    error E000068-0001

    Hi There i have a canon IR 6075i that is giving me error code E000068-0001 can anyone direct me as to what the fault is and any advice

  2. #2
    Field Supervisor 500+ Posts Luther's Avatar
    Join Date
    May 2006
    Location
    crystal lake ,Illinois
    Posts
    682
    Rep Power
    44

    Re: error E000068-0001

    Title Pre-transfer charging high voltage output leak error
    Remedy 1. Check the connection between the Main Driver PCB (PCB2) and the High Voltage Unit.
    Main Driver side: J112, High Voltage Unit side: J3098
    2. Check the connection between the Relay PCB (PCB5) and the High Voltage Unit.
    Relay side: J519, High Voltage Unit side: J3099
    3. Replace the Pre-transfer Charging Assembly.
    4. Check the connection inside of the High Voltage Unit.
    Check the connection of the High Voltage Unit Relay (J3098) and the Transfer High Voltage PCB (J3544).
    Check the connection of the High Voltage Unit Relay (J3099) and the Pre-transfer Charging PCB (J3545, J3500)
    5. Replace the Main Driver PCB (PCB2).
    6. Replace the Pre-transfer High Voltage Connector (FM4-1007).
    7. Replace the Pre-transfer Transformer (Post Charging Trance) of the High Voltage Unit.

  3. #3
    Service Manager 1,000+ Posts vigour's Avatar
    Join Date
    Aug 2010
    Posts
    1,034
    Rep Power
    42

    Re: error E000068-0001

    Had one this week.
    Pretransfer spring was broken.

  4. #4
    Service Manager 10,000+ Posts
    error E000068-0001

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: error E000068-0001

    Pre-Transfer.pdf

    In the case of replacing the Charging Wire on a Charging Wire basis, be sure to use the dedicated Charging Wire Tension Spring (97-5527) [A]. Do not use the Spring [B] attached to the Charging Wire.

    ch.JPG
    When removing the Primary Charging Assembly and the Pre-transfer Charging Assembly, go through the following procedure while the Charging Shutter is open.
    -At sleep mode, press the Power Switch on the Control Panel, check that the machine is in standby condition, turn OFF the Main Power, and then perform removing.
    In the case that the condition of the Charging Shutter (open/close) is unknown while the power of the host machine is OFF, turn ON the power, check that the machine is in standby condition, turn OFF the Main Power, and then perform removing.
    -If the above operations are not performed, it may be possible to remove the assembly while the Charging Shutter is closed, which may damage the drum or the shutter.
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  5. #5
    Tech Specialist 1,000+ Posts Canuck's Avatar
    Join Date
    Nov 2007
    Location
    Southwestern Ontario
    Posts
    1,713
    Rep Power
    63

    Re: error E000068-0001

    Yeah replace pre-transfer wire. It comes with spring already attached to it. Do a proper shutdown to make sure shutter moves to proper position. Dump the toner in the assembly also

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here