Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6
  1. #1
    Trusted Tech 50+ Posts
    Join Date
    May 2013
    Posts
    53
    Rep Power
    23

    another code ir 3200 e000012 0001

    need more help what is this code ?bad drum,,,thanks again

  2. #2
    Service Manager 10,000+ Posts
    another code ir 3200 e000012 0001

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: another code ir 3200 e000012 0001

    Quote Originally Posted by rdc View Post
    need more help what is this code ?bad drum,,,thanks again


    Probably a missing 24v issue Drum ITB Motor (M1) --check for 24v

    ++++ Check and/or replace the Double Switch PCB Assembly (FG6-9015-000) located in the rear of the copier behind the DC controller.


    24V I/L supply (to the ITB Motor (M1)) passes through Fuser Carriage switches MSW 5/6, Front Cover Open/ Closed detection switches MSW 1/2, and Manual Feed unit Open/ Closed detection switches MSW 3/4.
    If the voltage is not present at the motor, trace it back to the fuse pcb.

    As the machine starts initial rotation, an E012-0001 error occurs.

    24 V DC is measured at J71 pin 1 and 0 V DC is measured on pin 3 (normally 24 V DC is measured on both pins). The 24 Volts on pin 1 is fed through all 6 interlock switches and back to pin 3. If you're missing the the voltage on pin 3, check the interlocks for an "open".


    Workaround :
    In this case there was an open in the front door interlocks.

    Below is a diagram of the printer with the interlocks highlighted in red.

    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  3. #3
    Tech Specialist 1,000+ Posts Canuck's Avatar
    Join Date
    Nov 2007
    Location
    Southwestern Ontario
    Posts
    1,713
    Rep Power
    63

    Re: another code ir 3200 e000012 0001

    That wonderful fuse pcb.....make sure none of your drums or itb assembly are seized

  4. #4
    Trusted Tech 50+ Posts
    Join Date
    May 2013
    Posts
    53
    Rep Power
    23

    Re: another code ir 3200 e000012 0001

    Had power at j71 connector pin 1and 3,,but lost it my fault,,what fuse should i check to regain power...thanks,,

  5. #5
    Service Manager 10,000+ Posts
    another code ir 3200 e000012 0001

    teckat's Avatar
    Join Date
    Jan 2010
    Location
    VA
    Posts
    16,106
    Rep Power
    244

    Re: another code ir 3200 e000012 0001

    Quote Originally Posted by rdc View Post
    Had power at j71 connector pin 1and 3,,but lost it my fault,,what fuse should i check to regain power...thanks,,
    Be safe and just replace FUSE PCB_-PART is cheap
    Did u check all door switches ?
    Any missing or low voltage at a switch will cause voltsge drop and contribute to error
    **Knowledge is time consuming, exhausting and costly for a trained Tech.**

  6. #6
    Trusted Tech 50+ Posts
    Join Date
    May 2013
    Posts
    53
    Rep Power
    23

    Re: another code ir 3200 e000012 0001

    yes checked all interlocks.. ok replace board...

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here