CLOSE UPPER COVER at Canon Ipf 605 fault

[archiforma]

Hi all,

I,ve got a problem with my CANON IPF 605 ploter

When switch the printer ON, on the LCD is :

CLOSE UPPER COVER , but the cover is closed, the printer looks like dead, do nothing, zero sound


ipf 605 close upper cover.jpg


Everyone know maybe how to fix it, which part have to be replaced ?


Regards

John

[archiforma]

ipf605 1.jpgipf605 2.jpgipf605 3.jpgipf605 4.jpgipf605 5.jpg

Hi all,

I,ve got a problem with my CANON IPF 605 ploter

When switch the printer ON, on the LCD is :

CLOSE UPPER COVER , but the cover is closed, the printer looks like dead, do nothing, zero sound


ipf 605 close upper cover.jpg


Everyone know maybe how to fix it, which part have to be replaced ?


Regards

John

more picture with errors before it happend )

[nathans]

ipf605 1.jpgipf605 2.jpgipf605 3.jpgipf605 4.jpgipf605 5.jpg





more picture with errors before it happend )

Was there ever a resolved fix for this? I am having a hard time trying to find a strait answer to this.

[charm5496]

I have had issues with power supplies and main controllers causing issues on the wide formats where you get a close cover message. Have you measured voltages and checked the switches for continuity? Most have an upper and lower switch on them.

[nathans]

I have had issues with power supplies and main controllers causing issues on the wide formats where you get a close cover message. Have you measured voltages and checked the switches for continuity? Most have an upper and lower switch on them.

I did. The switches are testing ok. I think i saw something that said that if the firmware could be updated. Then the close upper cover would go away. I got into download mode and can't upload the firmware with the firmware tool. It says it needs to be in print mode. so that and i saw there was someone who had to replace the Main PCB.

[charm5496]

if you can I would make sure all of the DC voltages are being output to all areas. I was missing 24v on the IPF-710 that I had this on, so that is why I replaced power supply first

[edsalmeron]

Hi all,

I,ve got a problem with my CANON IPF 605 ploter

When switch the printer ON, on the LCD is :

CLOSE UPPER COVER , but the cover is closed, the printer looks like dead, do nothing, zero sound


ipf 605 close upper cover.jpg


Everyone know maybe how to fix it, which part have to be replaced ?


Regards

John

Hi, John

This same issue has come into the light to me. I had to dissassembly my plotter and I found out that when i turn it on in service mode that open cover issue shows up, but when i do it as a normal user it gives me this error
E196-404E

I've looked for it in the Service manual and though it is refered as a main PCB error, I think this issue seems to be a loop which may be caused by the photosensor located below the cover. As soon as I replace this, I'll let you know.

Greetings,
Ed

[Jack76]

Hi, John

This same issue has come into the light to me. I had to dissassembly my plotter and I found out that when i turn it on in service mode that open cover issue shows up, but when i do it as a normal user it gives me this error
E196-404E

I've looked for it in the Service manual and though it is refered as a main PCB error, I think this issue seems to be a loop which may be caused by the photosensor located below the cover. As soon as I replace this, I'll let you know.

Greetings,
Ed

Hola a mi me pasa lo mismo. Conseguiste solucionarlo?

[sales@tps-ni.com]

Hi, John

This same issue has come into the light to me. I had to dissassembly my plotter and I found out that when i turn it on in service mode that open cover issue shows up, but when i do it as a normal user it gives me this error
E196-404E

I've looked for it in the Service manual and though it is refered as a main PCB error, I think this issue seems to be a loop which may be caused by the photosensor located below the cover. As soon as I replace this, I'll let you know.

Greetings,
Ed

Hi just for reference I have replaced upper/top cover sensor and it made no difference.
Next I will try the main PCB